Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
• Carefully obey the instructions for electrical connections. There is the risk of injury from electrical current. • Disconnect the appliance from the electrical supply, before you do the maintenance work or you clean it. • The electrical mains terminal is live. • Make electrical mains terminal free of voltage. • Install correctly to give anti-shock protection. • A loose and incorrect mains plug and socket connections can make the terminal become too hot. • A qualified electrician must install the clamping connections correctly. • Use a strain relief clamp on cable. • Use the correct mains connection cable and replace the damaged mains cable with applicable cable. Speak to your local Service Force Centre. • The appliance must have the electrical installation which lets you disconnect the appliance from the mains at all poles with a contact opening width of minimum 3 mm. • If the fixing bracket is near to the terminal block, always make sure the connection cable does not come in contact with the edge of the bracket. • You must have correct isolation devices: line protecting cut-outs, fuses (screw type fuses removed from the holder), ground leakage trips and contactors. Disposal of the appliance • To prevent the risk of physical injury or damage – Disconnect the appliance from the power supply. – Cut off the mains cable where it connects with the appliance and discard it. – Flat the external gas pipes if there are fitted. – Speak to your local authorised facilities for disposal of your appliance. INSTALLATION WARNING! The following instructions about installation, connection and maintenance must be carried out by qualified personnel in compliance with standards and local regulations in force. Installation 7 Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S. 813 Current Editions and the ETCI Rules for Electrical Installations. Provision for ventilation Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Par. 2 and B.S. 6891 Current Editions. The hob should not be installed in a bed sitting room with a volume of less than 20 m.. If it is installed in a room of volume less than 5 m. an air vent of effective area of 100 cm. is required. If it is installed in a room of volume between 5 m. and 10 m. an air vent of effective area of 50 cm. is required, while if the volume exceeds 11 m. no air vent is required. However, if the room has a door which opens directly to the outside no air vent is required even if the volume is between 5 m. and 11 m.. If there are other fuel burning appliances in the same room, B.S. 5440 Part 2 Current Edition, should be consulted to determine the requisite air vent requirements. For appliances installed in the Republic of Ireland please refer to the NSAI- Domestic Gas Installation I.S. 813 Current Editions Table Four. Location The hob may be located in a kitchen, a kitchen/diner or bed sitting room (with a volume greater than 20 m.), but not in a bathroom or shower room. The minimum distance combustible material can be fitted above the hob in line with the edges of the hob is 400 mm. If it is fitted below 400 mm a space of 50 mm must be allowed from the edges of the hob. For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S 813 Current Edition Section 7- Permitted Locations of Appliance. Gas Connection WARNING! Any gas installation must be carried out by a GAS SAFE REGISTER installer. Make sure that, once the hob is installed, it is easily accessible for the engineer in the event of a breakdown. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this instruction booklet be ignored. On the end of the shaft, which includes the G 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force. 8 8 Installation 1 2 3 1 2 3 End of shaft with nut Washer Elbow Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper. The connection should be suitable for connecting to R 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Make sure that the main connection pipe does not exert any strain on the hob. If you use flexible metal pipes make sure that they agree to ISO 10380 and ISO 10807 standards. Be careful they do not come in touch with mobile parts or they are not squeezed. Also be careful when the hob is put together with an oven. It is important to install the elbow correctly, with the shoulder on the end of the thre...
Эта инструкция также подходит к моделям:Варочные панели - HG654440SM (622.62 kb)
Варочные панели - HG654440SM (622.62 kb)
Варочные панели - HG654440SM (622.62 kb)