Оценок - 4, средний балл: 4.3
(
)
)
|
Фото и характеристики Spirit XE295 |
Фрагмент инструкции
Make sure the Console Mast Cover (41) is facing the correct way. 2. At the top opening of the Main Frame (1), there is a Computer Cable (31) tied to a twist tie wire. Feed the twist tie wire and Computer Cable (31) into the bottom of the Console Mast (12) and out of the opening at the top. 3. Install the Console Mast (12) into the receiving bracket on the top of the Main Frame (1). Note: there is one bolt already installed in the receiving bracket that will engage with the slot at the bottom of the Console Mast. This needs to be tightened last, after the three other console mast bolts. 4. Place a Split Washer (96) onto the Hex Head Bolt (60) and hand tighten through the left side of the console mast. Place a Curved Washer (84) onto each Hex Head Bolt (103) and thread both into the front of the console mast tube. Fasten these front bolts as tight as possible with the wrench (106). Next firmly tighten the two left side bolts with the same wrench. NOTE: The Computer Cable (31) runs through the Console Mast (12). Be careful not to pinch this cable during this procedure because it may affect the electrical functions of the console. 5. Connect the two Hand pulse cables (36), Resistance cable (124), and Computer Cable (31) to the back of the console (30). Do not force the connectors; they will only fit one way and are different sizes to prevent confusion. Store the excessive cable in the Console Mast tube (12). 6. Attach the Console (30) to the bracket of the console mast tube with four Phillips Head Screws (66). Tighten the screws with the Phillips Head Screw Driver (108). HARDWARE STEP 1: Console Mast #96. 3/8” x 2T Split Washer (1 pc) #84. 3/8” x 23 x 1.5T Curved Washer (2 pcs) #66. M5 x 10mm Phillips Head Screw (4 pcs) #103. 3/8” x 3/4” Hex Head Bolt (2 pcs) #60. 3/8” x 2-1/4” Hex Head Bolt (1 pc) XE295 Elliptical Trainer 6 1. Slide two Wave Washers (81) onto both the Left and Right Console Mast axle. 2. Slide the Swing Arms (L) and (R), (10 & 11) onto the appropriate side of the axle. Note: Make sure the arms are attached as shown in the illustration. 3. Place a Flat Washer (97) onto each Hex Head Bolt (103) and fasten in the end of the left and right axle. Tighten with the wrench (106). 4. Slide the grommet (123) onto the Resistance cable (124); connect the two Resistance cables (124 & 125) and store the excess cable in the Console Mast tube (12) after snapping the grommet into the hole of the console mast tube. HARDWARE STEP 2: Swing Arms #97. 3/8” x 30mm Flat Washer (2 pcs) #81. 25mm Wave Washer (4 pcs) #103. 3/8” x 3/4” Hex Head Bolt (2 pcs) #123. Grommet (1 pc) 7 XE295 Elliptical Trainer 1. Untie the twist tie that holds each bushing (22) to the Connecting Arm end. Align the hole in the end of the Connecting Arms (L & R) (8 & 9) with the hole in the bracket of the Swing Arms (L) and (R), (10 & 11). The Connecting Arm ends should be inside of the Swing Arm (L) and (R), (10 & 11) brackets. Slide a Hex Head Bolt (104) through each Swing Arm (L) and (R), (10 &11) bracket and each Connecting Arm end. 2. Slide a Flat Washer (80) onto each bolt, then fasten the arms together by tightening a Nyloc Nut (71) to each bolt using the wrenches provided (109 & 106) wrenches. HARDWARE STEP 3: Connecting Arm #80. 5/16” x 20 x1.5T Flat Washer (2 pcs) #71. 5/16” Nyloc Nut (2 pcs) #104. 5/16” x 1-1/4” Hex Head Bolt ( 2 Pcs) STEP 4: Plastic Parts 1. Mate the Connecting Arm Covers (R) (58) with the Connecting Arm Covers (L) (58-1) on left and right Connecting Arms (8 & 9). Make sure these covers are oriented the correct way.There is an arrow ^ mark on the inside. Fasten together with four Phillips Head Screws (105) and four Sheet Metal Screws (87).Tighten with the Short Phillips Head Screw Driver (107).Then mate the Connecting Arm Covers (R) (57) with (L) (57-1) on Swing Arm (L) (10) and Swing Arm (R) (11), respectively. Fasten together with four Phillips Head Screws (105) and four Sheet Metal Screws (87).Tighten with the Short Phillips Head Screw Driver (107). 2. Fasten the two Wheel Covers (52) to the roller sets with four Phillips Head Screws (105).Tighten with the Phillips Head Screw Driver(108). 3. Attach the left side cover (19) and right side cover (20) to the mid-stabilizer tube with two Phillips Head Screws (105).Attach the right side cover (20) and left side cover (19) to the rear stabilizer tube with two Phillips Head Screws (105).Tighten all four screws with the Phillips Head Screw Driver (108).Then attach the Front Stabilizer Cover (49) with two Phillips Head Screws (105).Tighten with the Phillips Head Screw Driver (108). 4. Install the Front Handle Bar Covers (L & R) (54 & 55) and Rear Handle Bar Covers (L & R) (54-1 & 55-1) over the Handle Bars axle connections with four Sheet Metal Screws (87) on each side.Tighten with the Phillips Head Screw Driver (108). 5. Look closely at the four floor levelers underneath the middle and rear of the elliptical. If any of these aren’t in contact with the floor, use the wrenc...