Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
13. SIDE OF WHEEL WITH LONGER PLASTIC AXLE NEEDS TO FACE THE WHEEL BRACKET. IMPORTANT!: TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! Install wheels (27) onto axle (28) and wheel bracket (25) with push caps (29) as shown. IMPORTANT!: DO NOT OVER TIGHTEN 14. 29 27 28 25 27 29 21 30 20 8 Carefully reposition entire assembly as shown: 12. 13. SIDE OF WHEEL WITH LONGER PLASTIC AXLE NEEDS TO FACE THE WHEEL BRACKET. IMPORTANT!: TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! Install wheels (27) onto axle (28) and wheel bracket (25) with push caps (29) as shown. IMPORTANT!: DO NOT OVER TIGHTEN 14. P/N 214573 03/04 14 15 03/04 P/N 214573 15. Install pole mount bracket (45) and reinforcement bracket (47) with carriage bolts (46) as shown. Tighten flange nuts (15) completely. 1 45 15 15 47 46 46 16. Attach spacers (32, 33) to pole mount bracket (45) with bolts (54), washers (20), and lock nuts (37) as shown. IMPORTANT! Tighten just until washers (20) stop moving. 45 20 20 37 54 20 20 33 32 32 33 17. 45 15 35 48 48 34 50 Assemble lanyard (34) to locking pin (35) as shown (FIG A). Attach covers (48) onto pole mount bracket (45) with carriage bolt (50) and nut (15) as shown. 50 FIG. A 34 35 Loop end of pin lanyard (34) over carriage bolt (50) as it passes through the pole mount bracket (45) during this assembly. IMPORTANT!: 17. 45 15 35 48 48 34 50 Assemble lanyard (34) to locking pin (35) as shown (FIG A). Attach covers (48) onto pole mount bracket (45) with carriage bolt (50) and nut (15) as shown. 50 FIG. A 34 35 Loop end of pin lanyard (34) over carriage bolt (50) as it passes through the pole mount bracket (45) during this assembly. IMPORTANT!: 18. Apply logo and height indicator labels (41) to adjustment rod (31) as shown. Attach handle parts (38, 39) to adjustment rod with screw (36), carriage bolts (26), and flange nuts (15) as shown. IMPORTANT!: Indicator labels should be applied as close to holes as possible to prevent labels from being damaged during height adjustment. 26 15 15 39 38 36 26 31 41 41 P/N 214573 03/04 16 Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05 m) mark with pin (35). 35 19. 20. Install spacers (51) onto backboard brackets (52), with bolts (53, 54) and lock nuts (55, 37) as shown. 53 51 37 54 52 55 IMPORTANT!: KEEP HARDWARE LOOSE UNTIL AFTER STEP 25 IS COMPLETED. 17 03/04 P/N 214573 21. 21. Identify elevator tubes (63 & 56). Toward Toward 63Upper Elevator tube Toward PoleBoard 56Lower Elevator tube Toward PoleBoard Attach lower elevator tubes (56) and counter balance spring (68) to backboard support brackets (52) using spacers (59), bolt (57), and nut (58) as shown. 56 58 59 57 56 52 68 59 P/N 214573 03/04 18 19 03/04 P/N 214573 22. Place board spacers (49) into board as shown.Starting with nuts (15) flush against bracket (52) secure rim (70) and bracket to backboard. IMPORTANT! For spring loaded rim assembly, refer to instructions included with rim hardware. NOTE: Rim mounting nuts and bolts supplied with rim hardware. NOTE: DO NOT use washers here on spring return style rims. 58 57 59 59 63 63 52 Refer To Instructions Included With Rim Hardware For Rim Assembly. 23. Attach upper elevator tubes (63) to backboard support brackets (52) using spacers (59), bolt (57), and nut (58) as shown. IMPORTANT!: TIGHTEN ALL HARDWARE FROM STEP 22-25 AFTER THIS ASSEMBLY IS COMPLETED. 62 70 62 62 62 15 49 49 52 58 58 65 64 56 1 66 66 57 67 56 67 24. Support pole on sawhorse. Attach backboard assembly to top pole section (1) as shown. Install pole cap (64). NOTE: Two people are recommended for this step. Use caution; elevator assembly is heavy. 24. Support pole on sawhorse. Attach backboard assembly to top pole section (1) as shown. Install pole cap (64). NOTE: Two people are recommended for this step. Use caution; elevator assembly is heavy. 57 63 67 58 1 58 63 67 66 51 25. Install upper elevator tubes (63) to triangle plates (66) as shown. Install handle assembly to lower elevator tubes (56) using bolt (57), spacers (67), and nut (58) as shown. NOTE: Before going on to next step, set adjustable system assembly to the 10’ (3.05 m) setting. 57 56 56 67 67 TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! P/N 214573 03/04 20 26. Insert bolt (57) through left side upper elevator tube (63), then stretch spring (68) onto bolt (57). Insert bolt (57) through right side upper elevator tube (63) and secure with nut (58). WARNING! USE EYE PROTECTION WHEN INSTALLING SPRINGS. 68 58 57 63 63 21 03/04 P/N 214573 SECTION D: INSTALL FRONT COVER & HANDLE 27. Upright system and fill base (8) with water (approx. 40 gallons) and snap fill cap (54) in place. 42 DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY ...