Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
The ProSpot Fitness® P-50 has a footprint of approximately 6.x 6.. The barbell is approximately 6’-6" long. Locate your ProSpot Fitness® P-50 away from any source of water. Do not allow any liquid to be near the machine or spilled on any electrical part. Do not insert any object into the electrical box. • Approximate assembly time is 1/2 hour. • A flat area of 6. x 8. will be required to assemble and properly use the ProSpot Fitness® P-50. • Enclosed you will find the following tools: • 3 mm Allen Wrench • 4 mm Allen Wrench • 6 mm Allen Wrench • 9/16" Allen Wrench • You will need the following tools and a helper to complete the assembly: • 16 mm Hex Head Wrench • 18 mm Hex Head Wrench • Floor Padding, such as cardboard, to avoid scratching your floor during assembly. • A good pair of scissors will be helpful in separating the parts from one another while removing them from the cartons. • HAND TIGHTEN all bolts. DO NOT fully tighten bolts until instructed to do so. • Before assembly, separate and identify the right-sided parts from the left-sided parts. These parts are easily distinguished by the manner in which the pre-drilled holes align with corresponding parts, or are identified by .L . & .R. stickers. • The ProSpot Fitness® P-50 uses different lengths of bolts. Be careful to use the correct length of bolt called for at each step of assembly. Refer to the sizing charts provided. • WARNING: Never perform any maintenance on the ProSpot Fitness® P-50 while the Power Supply is plugged into the wall !!! ALWAYS REMEMBER: After the initial set up of the system or after performing any service on the unit, RESET the Computer on your ProSpot system before using it. Just unplug the power supply from the Electronic Box, wait 30 seconds and plug back in. Resetting the Computer allows it to recalibrate and work to its greatest efficiency. -- 2 - STEP # 1: P-50 MAIN FRAME ASSEMBLY 1. Place the two main pre-assembled side frames left & right respectfully opposite each other in the center of the assembly area as shown in the Illustration. Place the Back Base Rail (3) between the two Side Base Rails (1 & 2) so that the side pre-drilled holes of the Base Rails (1 & 2) align with the end holes of the Back Base Rail (3). 2. Attach the two main pre-assembled side frames to the Back Base Rail (3) using two Cross Brace Backing Plates (4), four bolts (66), eight washers (77) and four nuts (81) as shown. HAND TIGHTEN the bolts at this time. 3. Now attach the two main pre-assembled side frames to the Top Rail (16) using four bolts (66), eight washers (77) and four nuts (81) as shown. HAND TIGHTEN the bolts at this time. 4. Attach Electronic Box Locating Board (11) to Back Base Rail (3) using two bolts (65), two washers (77) and two nuts (81). 5. Tighten all bolts and nuts used for assembly in previous steps. 6. Carefully thread both Base Wire Harness’s thru the center hole in the Back Base Rail (3). 7. Plug in both Base Wire Harness’s into sides of Electronic Box (13). 8. Install Protective Cover (12) over Electronic Box with two screws (70). 9. Snap both Base Wire Harness’s into Channels (90) and push any excess into hole in Side Base Rails (1& 2). 10.Untie the coiled left & right Weight Bar Cables, so that they hang straight down with out any twists or tangles. Be sure that the cables are straight and uncrossed and cables and pulleys move smoothly. STEP #2: SENSOR WEIGHT BAR INSTALLATION 1. Standing in front of the ProSpot Fitness® P-50. Insert one end and then the other end of the Sensor Weight Bar (31) into the Cable Knuckles (46-48). Slide the Cable Knuckles onto the Bar until they rest snugly against the preinstalled sensor retaining collars (45 & 48) at each end of the Sensor Weight Bar (31). (There is a rotation-limiting pin that protrudes from the bottom of the Sensor Weight Bar (31) that must fit through a slot in the knuckles (46-48) as it is slid into position). 2. Place one Plastic Locking Sleeve (36) onto each end of the Sensor Weight Bar (25) and slide them inwards until they butt up against and secure the Weight Bar Cable Knuckle in place. Tighten Plastic Locking Sleeve bolts securely with 4mm Allen wrench (95) provided. 3. Place one of the Olympic Adapters (32) onto the Sensor Weight Bar (31) and slide them onto the Bar, then insert the Weight Bar Shoulder Bolt (34) onto each end of the Sensor Weight Bar (31). Secure with provided 9/16" Allen wrench (97). -- 3 - -- 4 - -- 5 - -- 6 - -- 7 - !!Read!! This Page Before Using Your ProSpot Fitness® Product Safe Use of Your ProSpot Fitness® Product 1. CAUTION: This machine involves the risk of possible injury by its user. THE FOLLOWING RULES SHOULD BE CARFULLY FOLLOWED: Consult a physician or other healthcare provider before beginning an exercise program. If you are in bad health or are handicapped, ask for the opinion of your physician and exercise only under qualified supervision. Discontinue to exercise if you experience any light-headedness, dizziness or shortness of...