Оценок - 3, средний балл: 5
(
)
)
|
Фрагмент инструкции
.. .... .. .... .... .... .. .... .... .. .. .... .. .... .. .... .... .... .... .... .... .... .. .. .... .... .... .... Complete Stand Component Diagram Tools Required 7/32" Allen Wrench (included) You will also need: 9/16" Socket 9/16" Wrench or Adjustable Wrench Utility knife or scissors to cut nylon ties Parts#Qty.Description11TUBE, BOTTOM CROSS BRACE21ASSEMBLY, REAR LEFT STABILIZER31ASSEMBLY, REAR RIGHT STABILIZER42ASSY, STAND LEG51WELDMENT, LEFT DUMBBELL PLATFORM61WELDMENT, RIGHT DUMBBELLPLATFORM71WELDMENT, TOWEL BAR81FOOT PEGS, SET OF FOUR91HOLD DOWN STRAPS, 2F 2M1020NUT-NL 0.375-16 G2-BlkZ1136WASHER-FLAT 0.375 REGULAR BLKZ128SCREW-BHCS 0.375-16x3.0 G2-BlkO134SCREW-BHCS 0.375-16x2.75 G2-BlkO144SCREW-BHCS 0.375-16x2.5 G2-BlkO154SCREW-FHCS 0.375-16x1.0 G2-BlkO161WHEELS, CASTER SET OF FOUR171PLATE, CENTER W/ LOGOHardware 2.5" 2.75" 3.0" Flat Head Button Head Lock Nut Flat Washer Button Head Button Head Qty Hardware Card A: 2.75" Screw, Button Head 4 2.5" Screw, Button Head 4 1.0" Screw, Flat Head 4 Nut, Lock 12 Washer, Flat 20 Hardware Card B: 3.0" Screw, Button Head 8 Nut, Lock 8 Washer, Flat 16 7/32" Allen Wrench 3 4 step 1 Parts: • Stand Leg (#4) • Rear Left Stabilizer (#2) Hardware Qty • 3" Screws (#12) 2 • Washers (#11) 4 • Nuts (#10) 2 Tools: • Hex Key (7/32”) 1-1 Attach the Rear Left Stabilizer (#2) to the Stand Leg (#4) using the hardware shown in Figure 1. Note: Do not tighten hardware. Figure 1 .. .. .... .... .... .... 5 step 2 Figure 2 Parts: • Stand Leg (#4) • Rear Right Stabilizer (#3) Hardware Qty • 3" Screws (#12) 2 • Washers (#11) 4 • Nuts (#10) 2 Tools: • Hex Key (7/32”) 2-1 Attach the Rear Right Stabilizer (#3) to the Stand Leg (#4) using the hardware shown in Figure 2. Note: Do not tighten hardware. .. .. .... .... .... .... Parts: • Cross Brace (#1) • Left Stand Leg assembly from Step 1 • Right Stand Leg assembly from Step 2 Hardware Qty • 3" Screws (#12) 4 • Washers (#11) 8 • Nuts (#10) 4 Tools: • Hex Key (7/32”) 3-1 Attach the Bottom Cross Brace (#1) to the Rear Left Stabilizer (#2) and Rear Right Stabilizer (#3) using the hardware shown in Figure 3. Make sure that the narrower edge of the Cross Brace (#1) is closer to the Stand Leg (#4) uprights. Note: Do not tighten hardware. step 3 6 .. .. .. .. .. .... .... .... Figure 3 7 step 4 Parts: • Stand Leg and Cross Brace assembly from Step 3 • Center Plate (#17) Hardware Qty • 2.5" Screws (#14) 4 • Washers (#11) 8 • Nuts (#10) 4 Tools: • Hex Key (7/32”) • Wrench/Socket (9/16”) or Adjustable Wrench 4-1 Install the Center Plate (#17) to both Stand Legs (#4) using the hardware shown in Figure 4. Note: Make sure that the Center Plate edges are on the outer sides of the legs, and that the logo on the Plate is right side up. 4-2 Tighten all hardware from Steps 1, 2 and 3 securely. .... .... .... .... .... .... .... .... .... Figure 4 step 5 8 Parts: • Stand base assembly from Step 4 • Left Dumbbell Platform (#5) Hardware Qty • 2.75" Screws (#13) 2 • Washers (#11) 4 • Nuts (#10) 2 Tools: • Hex Key (7/32”) • Wrench/Socket (9/16”) or Adjustable Wrench 5-1 Secure the Left Dumbbell Platform (#5) to left Stand Leg (#4) using the hardware shown in Figure 5. Note: Make sure the screw holes in the Platform are toward the center of the stand. .. .... .... .... .... Figure 5 9 step 6 Parts: • Stand base assembly from Step 5 • Right Dumbbell Platform (#6) Hardware Qty • 2.75" Screws (#13) 2 • Washers (#11) 4 • Nuts (#10) 2 Tools: • Hex Key (7/32”) • Wrench/Socket (9/16”) or Adjustable Wrench 6-1 Secure the Right Dumbbell Platform (#6) to right Stand Leg (#4) using the hardware shown in Figure 6. Note: Make sure the screw holes in the Platform are toward the center of the stand. .... .... .... .. .... Figure 6 step 7 10 Parts: • Stand assembly from Step 6 • Towel Bar (#7) Hardware Qty • 1" Screws (#15) 4 • Washers (#11) 4 • Nuts (#10) 4 Tools: • Hex Key (7/32”) • Wrench/Socket (9/16”) or Adjustable Wrench 7-1 Attach the Towel Bar (#7) to the Left Dumbbell Platform (#5) and the Right Dumbbell Platform (#6) using hardware shown in Figure 7. Hand tighten screws in a cross pattern, to ensure even fit. 7-2 Tighten all screws securely. .. .... .... .... .... .... .... Figure 7 Parts: • Stand assembly from Step 7 • Foot Pegs (#8) or Caster Wheels (#16) • Hold Down Straps (#9) 8-1 Attach either Foot Pegs (#8) or Caster Wheels (#15) to the Rear Left Stabilizer (#2), the Rear Right Stabilizer (#3), and both Stand Legs (#4). See Figure 8. 8-2 Attach the Hold Down Straps (#9) to the Left Dumbbell Platform (#5) and the Right Dumbbell Platform (#6) as shown in Figure 8. 11 step 8 .. .... .. Figure 8 16400 SE Nautilus Dr. Vancouver, Washington, USA 98683 1-800-NAUTILUS © 2006 Nautilus, Inc. All Rights Reserved. Bowflex and Bowflex SelectTech are either registered trademarks or trademarks of Nautilus, Inc. Specifications subject to change. P/N 000-3708 RevB 02/06 ...