Lift the rear of the printer cover to remove. To re-install, hook the pawls on the cabinet and close. Caution: The paper cutter is mounted on the printer cover. Be careful not to cut yourself. 2 Printer RS-232C connector Operator display Receipt paper Drawer lock Drawer Printer cover Customer display (Pop-up type) Mode switch Power cord Keyboard Take-up spool Print roller release rever Print roller arm Inner cover Paper roll cradle Paper positioning guides Do not attempt to remove the paper roll

. . . . . . . . . . . . . . . . . . . . . . . . . . . 1 CHAPTER 2. OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 CHAPTER 3. MASTER RESET AND PROGRAM RESET. . . . . . . . . 6 CHAPTER 4. HARDWARE DESCRIPTION . . . . . . . . . . . . . . . . . . . . 7 CHAPTER 5. DIAGNOSTIC PROGRAM . . . . . . . . . . . . . . . . . . . . . 14 CHAPTER 6. IPL FROM EP-ROM . . . . . . . . . . . . . . . . . . . . . . . . . . 19 CHAPTER 7. CIRCUIT DIAGRAM AND PWB LAYOUT . . . . . . . . . 2

. Enlargement At the receipt side, the logo is also printed and the receipt is issued. 3 Check that: The print is free from contamination, blur, and uneven density. 4 End of testing The test will end automatically. 4) KEYBOARD TEST 1 Key operation _ _ _ _104 3 CA/AT 2 KEY check sum code 2 Test procedure The keyboard is checked using the sum check code of the key code. If the sum check code is not entered, the check is made using the sum check code of the default keyboard arrangement The sum chec

Before you set up the cash register, prepare three new alkaline batteries LR6 ("AA" size) which are necessary for memory backup. Find a stable and flat surface not subject to direct radiation, to place the cash register. English 1 Initializing the Cash Register To ensure the cash register operates properly, please use the following procedure: 1. Make sure the power cord is unplugged and batteries are not installed on the register. 2. Insert the manager (MA) key into the mode switch and turn it t

Place the cash register on a stable, flat surface not subject to direct sunlight. 1 Connecting the Barcode Scanner A barcode scanner is provided with the cash register. To use the scanner, connect the scanner before turning on the register. 1. Open the Scanner port cover at the right side of the register. 2. Insert the connector of the barcode scanner into the Scanner port, and tighten both screws on the connector. CAUTION: • Always unplug the power cord of the cash register when you connect or

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation

If the no battery symbol “ l ” appears, you must install the batteries at once. Install three new alkaline batteries LR6 (“AA” size) according to the procedure shown below with the AC cord connected and the mode switch set to the REG position: 1. Push the printer cover forward and detach it. Be careful with the paper cutter, so as not to cut yourself. 2. Open the battery compartment cover next to the paper roll cradle. 7 3. Insert three new alkaline batteries LR6 (“AA” size) as illustrated

(Fixed position) 0 F Always enter 0. (Fixed position) 0 G Always enter 0. (Fixed position) 0 H Number of purchases print Allow printing of number of purchases* 0 Disallow it 1 Function selection for tax Job code: 15 * Item: A B C D E F G Always enter 0. Always enter 0. Always enter 0. Always enter 0. Always enter 0. Always enter 0. Tax delete in REG mode availability Selection: (Fixed position) (Fixed position) (Fixed position) (Fixed position) (Fixed position) (Fixed position) Allow tax delete

Message display·····································································································································4 (1) Message displayed during inline communication··············································································4 (2) Error messages·································································································································5 2. Open store operation (OPXZ mode) – master and satellite ·············

Immediately after this, the new data is automatically distributed to all other machines to update the PLU/EAN main files or dynamic PLU/EAN files which contain the code of the item. The data on an EAN item whose price has been changed at a satellite is also stored in the T-LOG buffer of the satellite. The data stored in the T-LOG buffer is collected by T-LOG polling at the master to update its PLU/EAN main file or dynamic EAN file. For further information on the price change function, see the UP