Push the printer cover forward and detach it. 2. Place a paper roll in the paper roll cradle so that the paper unrolls from the bottom. Tax 1 @/TM @/TM Tax rate (7.0000%) Min. taxable amount ($0.11) #/ SBTL Changing Other Settings As Necessary Your cash register is pre-programmed so that you can use it with minimum setup. To change the initial settings, see the appropriate sections. Initial Settings Departments 1 to 4: Taxable 1. Positive (+). Preset price: 0.00 Departments 5 to 8: Non-taxable.

Place the cash register on a stable, flat surface not subject to direct sunlight. 1 Connecting the Barcode Scanner A barcode scanner is provided with the cash register. To use the scanner, connect the scanner before turning on the register. 1. Open the Scanner port cover at the right side of the register. 2. Insert the connector of the barcode scanner into the Scanner port, and tighten both screws on the connector. CAUTION: • Always unplug the power cord of the cash register when you connect or

s. A (Smallest amount for which tax must be collected.) *Up to 4 types of tax are programmable. Example1: Set state tax 6.25% with tax exempt as 12. s9@ 1@ 6P25@ 12 sA Tax 1 Tax rate (6.25%) Min. taxable amount ($0.12) Example2: Set state tax 4% with tax exempt as 0. s9@ 1@ 4 sA Tax 1 Tax rate (4%) Other Programming While the cash register is pre-programmed so it can be used with minimal set-up, it does provide you optional features. For details, please refer to the instruction manual. Initial s

Before you set up the cash register, prepare three new alkaline batteries LR6 ("AA" size) which are necessary for memory backup. Find a stable and flat surface not subject to direct radiation, to place the cash register. English 1 Initializing the Cash Register To ensure the cash register operates properly, please use the following procedure: 1. Make sure the power cord is unplugged and batteries are not installed on the register. 2. Insert the manager (MA) key into the mode switch and turn it t

Lift the rear of the printer cover to remove. To re-install, hook the pawls on the cabinet and close. Caution: The paper cutter is mounted on the printer cover. Be careful not to cut yourself. Printer2 Operator display Receipt paper Drawer lock Drawer Printer cover Customer display (Pop-up type) Mode switch AC power cord Keyboard Take-up spool Print roller release rever Print roller arm Inner cover Paper roll cradle Paper positioning guides Do not attempt to remove the paper roll with the print

Lift the rear of the printer cover to remove. To re-install, hook the pawls on the cabinet and close. Caution: The paper cutter is mounted on the printer cover. Be careful not to cut yourself. 5 Paper roll cradle (Receipt side) Print roller release lever (Receipt side) Print roller arm (Receipt side) Paper positioning guides Inner cover Take-up spool Paper roll cradle (Journal side) Print roller release lever (Journal side) Print roller arm (Journal side) Do not attempt to remove the paper roll

Lift the rear of the printer cover to remove. To re-install, hook the pawls on the cabinet and close. Caution: The paper cutter is mounted on the printer cover. Be careful not to cut yourself. 2 Printer RS-232C connector Operator display Receipt paper Drawer lock Drawer Printer cover Customer display (Pop-up type) Mode switch Power cord Keyboard Take-up spool Print roller release rever Print roller arm Inner cover Paper roll cradle Paper positioning guides Do not attempt to remove the paper roll

Message display·····································································································································4 (1) Message displayed during inline communication··············································································4 (2) Error messages·································································································································5 2. Open store operation (OPXZ mode) – master and satellite ·············

Immediately after this, the new data is automatically distributed to all other machines to update the PLU/EAN main files or dynamic PLU/EAN files which contain the code of the item. The data on an EAN item whose price has been changed at a satellite is also stored in the T-LOG buffer of the satellite. The data stored in the T-LOG buffer is collected by T-LOG polling at the master to update its PLU/EAN main file or dynamic EAN file. For further information on the price change function, see the UP

For department 41-99: To program zero dsDept. code Unit price (max. six digits) A To program another department, start from the beginning without pressing the Akey. Key operation example Print 1000 . A Unit price If a department is not programmed to allow the entry of preset unit prices in functional programming, the department is automatically changed to allow the entry of preset unit prices by this programming entry. 2 PLU/UPC Programming The cash register can handle PLU codes and UPC codes. P