Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
This thermostat will automatically cut off in Heat mode if the temperature rises above 95°F (35°C), and automatically cut off in cool mode if the temperature drops below 45°F (7°C). Read This Before Installing Thermostat (continued) POWER FAILURE 7 7 Whenever the main power is interrupted or fails, the battery power retains the programs and current time. AUTO RECOVERY 8 8 Your thermostat is set from the factory to gradually recover the room temperature from an energy saving program to your comfort program. Therefore, the thermostat may turn your system on several minutes prior to your programmed time. This operation is normal, but can be turned off. Refer to the Selector Switches information on page 24. BATTERY WARNING 9 9 Fresh alkaline batteries should provide over one year of service. However, when the batteries become drained, the Low Battery indicator will flash on the display. When this message occurs, install 2 new AA batteries. You have approximately 1 minute to ENERGY STAR® Partner As an ENERGY STAR® Partner, Climate Technology has determined that this programmable thermostat meets the ENERGY STAR® guidelines for energy efficiency. change the batteries and keep thermostat’s clock and program settings. Once the batteries have become too low to ensure proper operation, your system will be turned Off, and the display will be cleared except for the Low Battery indicator flashing on the LCD display. CAUTION: Once the Low Battery only display occurs, the thermostat is shut down, and your system will no longer operate. In this condition, there is no temperature control of your dwelling. NOTE: The INDIGLO® night-light will not function when the thermostat is in low battery condition. NOTE: If you plan to be away from the premises over 30 days, we recommend that you replace the old batteries with new alkaline batteries prior to leaving. Features Home Today: Overrides LCD Display: Shows time, day, temperature, program energy-saving programnumber, and other feature information as required. temperatures while you are energy home today fan auto on system heat cooloff reset program filter hold /return HEAT TEMP AM SA 2 Program Day Key: Selects the day or days to review or change in the Program mode. Energy: Measures and displays heating and cooling system operating time for Today, Yesterday, This Week, Last Week, or Total. By monitoring your energy usage, you can program the thermostat to optimize energy savings. System Switch: Selector switch for Heat, Cool, and Off Fan Switch: Fan switch for Automatic or Continuous fan operation. home for the day. day/time prog day Reset: Press with a paper clip to reset the thermostat and return to power-up settings. Up and Down Keys: Keys for changing the Temperature setting. Also used for increasing and decreasing selections in the Time, Program, and Span functions. Program Key: Used for entering and modifying Programs. Use with the Up and Down keys to set times and temperatures. Press when in Clock setting mode to select between 12 and 24 hour clock modes. Filter Key: Resets Filter Change counter to zero. Day / Time Key: Used for entering the Clock setting mode. Use with the Up and Down keys to set the time and day. Hold / Return Key: Used for setting a permanent or vacation hold, and for returning to the normal display from Day & Time setting, Programming, or Span setting modes. Battery Release Lever: Push to pop batteries loose. 8INSTALLATION INSTALLATION What You Need This thermostat includes two #8 screws and two wall ¦ Phillips and Slotted Screwdrivers anchors for mounting. To install your thermostat, you ¦ Hammer should have the following tools and materials. ¦ Electric drill and 3/16" bit ¦ Two 1.5 V (AA) size alkaline batteries (included) Remove Old Thermostat CAUTION: Do not remove any wiring from existing thermostat before reading the instructions carefully. WIRES MUST BE LABELED PRIOR TO REMOVAL. ¦ IMPORTANT! Turn off the power to the furnace at the main power panel or at the furnace. ¦ Remove existing thermostat cover. See Figure 1. Some thermostats will have screws or other locking devices that must first be removed. Once wall mounting plate is exposed, look for wires. If wires are not visible, they may be connected to the back of the wallplate. Again, look for screws, tabs, etc. Some models have doors that open to expose wires and mounting screws. (See Figure 1). TYPICAL HOME THERMOSTATS Figure 1 Wall Mounting Plate Thermostat Cover Wall Mounting Plate Thermostat Cover Wire Labeling ¦ Each wire coming from the wall to the existing thermostat is connected to a terminal point on that thermostat. Each of these terminal points is usually marked with a code letter as shown in Table A on the next page. ¦ Note that this thermostat has multiple function terminals that allow Single-Stage Heat Pump capability. Standard systems use: Rh, Rc, G, W. [Single-Stage Heat Pumps use: Rh, Y1, G, and O or B.] Table A below shows the multiple functions of the terminals. Use the te...
Эта инструкция также подходит к моделям:Термостаты - 43355 (454.04 kb)
Термостаты - 43355 (454.04 kb)