Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
During this period, AUBE Technologies Inc. will repair or replace, at our option and without charge, any defective product which has been used under normal conditions. The warranty does not cover delivery costs and does not apply to products poorly installed or randomly damaged following installation. This warranty cancels and replaces any other manufacturer's express or implied warranty as well as any other company commitment. AUBE Technologies Inc. cannot be held liable for related or random damages following the installation of this product. The defective product as well as the purchase invoice must be returned to the place of purchase or mailed, prepaid and insured, to the following address: Aube Technologies Inc. 705 Montrichard Saint-Jean-sur-Richelieu, Quebec, Canada J2X 5K8 If you have any questions concerning the TH113 or the TH116 thermostat, call our technical support team at: Phone: Montreal area: (450) 358-4600 Canada / U.S.: 1-800-831-AUBE (2823) Fax: y(450) 358-4650 Email: service@aubetech.com Monday to Friday from 8:30 AM to 5:00 PM EST. For more information on our products, visit us at: & ' Follow the same procedure for the TH116. Power base Control module &' .. .. ( ' 01/08/03 920-113-001-00-1-A PB112-024T 400-112-000-B 18/1/06 1/1 The PB112-024T power base can be used on any TH11x series thermostat (with the exception of the TH110 model). This low-voltage power base operates on 15-minute cycles and can be connected to a line-voltage load using a relay or directly to a 24-volt device. The PB112-024T is compatible with most relays; however, the following Aube relays are optimized for use with this power base: • RT850 solid-state relay (SSR) • RT850T solid-state relay (SSR) with built-in 24-V transformer • RC840 electromechanical relay • RC840T electromechanical relay with built-in 24-V transformer .. One (1) power base .. Two (2) plastic anchors .. Two (2) mounting screws .. For a new installation, choose a location about 1.5 m (5 ft.) above the floor. .. The thermostat must be installed on an inside wall facing the heating system (except for floor heating systems). .. Avoid locations where there are air drafts (top of staircase, air outlet), dead air spots (behind a door), direct sunlight or concealed chimney or stove pipes (except for floor heating systems). The installation must be carried out by an electrician and comply with local electrical codes. .. Turn off power to the heating system at the main electrical panel to avoid electrical shock. .. Wire the base according to your application. See typical wiring diagrams in sections 4.1 to 4.4. .. For a floor heating system installation, connect the floor sensor between the S and R terminals. .. Secure the base to the wall using the provided screws and wall anchors. .. Configure the switches located on the control module (if any). Refer to the user guide. .. Install the control module onto the base. .. Apply power to the heating system. .. Verify the installation by checking that the heating system can be turned on or off using the thermostat. 4.1 Single SSR with Built-in Transformer 4.2 Multiple SSRs with External Transformer 4.3 Electromechanical Relay with External Transformer 4.4 Hot Water Heater Valve Maximum load: 0.5 A / 24 VAC Heating cycle length: 15 minutes Operating temperature: 32°F to 122°F (0°C to 50°C) Storage: -4°F to 122°F (-20°C to 50°C) Size (H • W • D): 124 x 70 x 23 mm (4.89 x 2.76 x 0.91 in) Wire gauge: 14 to 22 AWG .. Applications 1. .. Supplied Parts 2. .. Installation Guidelines 3. .. Installation Procedure 4. .. Technical Specifications 5. Electrical Panel Heater Blue Red Black Electrical Panel Heater Heater External 24 V Transformer Red Red Black Black Electrical Panel Heater External 24 V Transformer Electrical Panel External 24 V Valve Transformer PB112-024T Installation Instructions 24 V Low-Voltage Power Base ...
Эта инструкция также подходит к моделям:Термостаты - TH113 A (307.81 kb)