Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
They should be available at most electronic stores. Connecting an Antenna or Wall Outlet Cable Connecting an Antenna or Wall Outlet Cable Note: The TV back panel and connections shown here are for reference only and may vary by model. VHF Antenna (Channels2-13) UHFAntenna (Channels 14-69 \\w\w\j — Flat Twin Lead External Antenna or Cable FlatTwin Lead — TV back panel (section detail) Figure 1. Connecting separate UHF and VHF antennas. Mitsubishi strongly recommends against using antennas with twin flat leads. Twin flat lead antenna wires are subject to interference which may adversely affect the performance of the TV. We recommend using coaxial antenna cable. Optional 3OO Ohm to 75 Ohm MatchingTransformer Figure 2. Connecting twin lead antenna, coaxial lead antenna, or wall outlet cable. Separate UHF and VHF Antennas (Figure 1) 1. Connect the UHF and VHF antenna leads to the UHF/VHF combiner. 2. Push the combiner onto ANT-A on the TV back panel. UHF/VHF combiners are not provided with the TV. They are available at most electronic stores. Note: This TV will only be able to provide an analog signal through ANT-A on the TV back panel. See page 5 for Outdoor Antenna Grounding information. Twin Lead Antenna, Coaxial Lead Antenna, or Wall Outlet Cable (Figure 2) For antenna with twin flat leads: 1. Connect the 300 Ohm twin leads to the transformer. 2. Push the 75 Ohm side of the transformer onto ANT-A on the TV back panel. 300 Ohm to 75 Ohm matching transformers are not provided with the TV. They are available at most electronic stores. For cable or antenna with coaxial lead: 3. Connect the incoming cable to ANT-A on the TV back panel. I IMPORTANT I Additional connection cables are not provided with the TV. They should be available at most electronic stores. Note: This TV will only be able to provide an analog signal through ANT-A on the TV back panel. See page 5 for Outdoor Antenna Grounding information. 14 Connecting an Antenna to a Cable Box or VCR Note: The TV back panel and connections shown here are for reference only and may vary by model. Cable Box (Figure 3) 1. Connect the incoming cable to ANT-A on the TV back panel. Connect two coaxial cables as follows: 2. One from LOOP-OUT on the TV back panel to IN on the cable box back panel. 3. One from OUT on the cable box back panel to ANT-B on the TV back panel. Note: If your cable box has separate audio/video outputs, please see Composite Video with Audio or S-Video with Audio, page 16 (Figure 6). Incoming Cable 1 Figure 3. Connecting the cable box. Antenna or Wall Outlet Cable (Figure 4) 1. Connect the incoming cable to ANT-A on the TV back panel. Connect two coaxial cables as follows: 2. One from LOOP-OUT on the TV back panel to ANTENNA IN on the VCR back panel. 3. One from VCR back panel ANTENNA OUT to ANT-B on the TV back panel. Note: If your cable box has separate audio/ video outputs, please see Composite Video with Audio or S-Video with Audio, page 16 (Figure 6). Figure 4. Connecting the VCR with antenna or wall outlet cable. Note: For models WS-48315, WS-55315, WS-65315 and WS-65315A, when the Energy Mode is set to Low, the VCR may not record programs when the TV is off. Note: For digital cable boxes, refer to your Digital Cable Box owner’s guide for instructions on optimal connections to this TV. 15 Connecting an Antenna to a Cable Box or VCR Connecting an Antenna to a Cable Box and VCR Connecting Audio/Video to the Cable Box or VCR Connecting an Antenna to a Cable Box and VCR, Connecting Audio/Video to the Cable Box or VCR Note: The TV back panel and connections shown here are for reference only and may vary by model. Contact your local cable or satellite provider or refer to the cable box or satellite Owner’s Guide for instructions on optimal connections to this TV. Cable Box (Figure 5) 1. Connect the incoming cable to ANT-A on the TV back panel. Connect three coaxial cables as follows: 2. One from LOOP-OUT on the TV back panel to IN on the back of the cable box. 3. One from OUT on the back of the cable box to ANTENNA IN on the VCR back panel. 4. One from ANTENNA OUT on the VCR back panel to ANT-B on the TV back panel. Note: For best performance, please see Composite Video with Audio or S-Video with Audio, below. Composite Video with Audio or S-Video with Audio(Recommended) (Figure 6) 1. Connect a video or an S-Video cable from VIDEO OUT on the VCR back panel to VIDEO or S-VIDEO, INPUT-1 or INPUT-2 on the TV back panel. 2. Connect a set of audio cables from AUDIO OUT on the VCR back panel to AUDIO INPUT-1 or INPUT-2 on the TV back panel, matching the input used in step 1. • The red cable connects to the R (right) channel • The white cable connects to the L (left) channel If your VCR is mono (non-stereo), connect only the white (left) cable. You may connect to the S-VIDEO or VIDEO terminal but not to both. Figure 6. Connecting the VCR Audio/Video. Figure 5. Connecting t...
Эта инструкция также подходит к моделям:Телевизоры - WS-48315 (3.78 mb)
Телевизоры - WS-55315 (3.78 mb)
Телевизоры - WS-48315 (3.78 mb)
Телевизоры - WS-55315 (3.78 mb)