Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
-You may be too far from the TV. You must be within 23 feet (7 meters). -Use the remote control while pointing it at the screen. You cannot select a certain channel -Make sure the channels have been programmed. See “Channel Summary” page 32. -Check to see if the channel is locked. See “Channel Summary - Lock” page 32. The power turns off by itself -Make sure the set did not become unplugged. -Perhaps the ON/OFF TIMER is set. See page 48. -Check to see if the Sleep Timer was set. See page 51. -Are the POWER LED and the ON TIMER LED on the front panel of the television blinking alternately? If you have just replaced the lamp, it is possible that the lamp has not been installed correctly. Try installing the lamp again. (Refer to the table on the next page.) It does not operate correctly This television is operated by a microprocessor. It is possible that external noise or interference is causing the problem. If the television does not function correctly, remove the electric plug from the wall outlet and wait a while before inserting it into the wall outlet again and operating the television. The clock is wrong The power was interrupted and the clock was not reset. See page 30. The color quality is poor -Tint and Color may be improperly adjusted. See page 38. -The VIDEO STATUS mode may be turned to the wrong setting. See page 41. There are lines across the picture There could be interference from another electrical appliance, such as a computer, another TV or VCR. Move any such appliances further away from the TV. The picture is spotted There could be interference a from high-wattage appliance, like a hairdryer or vacuum, operating nearby. Move the antenna away from the appliance or change to a coaxial cable connection which is less prone to interference. There are double pictures (ghosts) A building or passing airplane can reflect the original signal and produce a second, slightly delayed one. Adjust your antenna position. Picture is snowy (image noise) Your antenna may be damaged, disconnected or turned. Check the antenna connection page 6 and in your Quick Setup Guide. If the antenna is damaged, replace it. Troubleshooting PROBLEMS CHECK Screen is 80% black The Closed Caption Text mode is on. Turn it off in the CLOSED CAPTIONMenu, see page 36. Stereo or bilingual programs cannot be heard Make sure the MTS settings are correct. See “MTS” on page 43. There is no sound from the TV’s speakers The TV Speaker option may be turned off. See page 44. Static electricity It is normal to feel static electricity if you brush or touch the screen. You hear occasional crackling sounds It is normal for the TV to make crackling sounds when first turned on or off. Unless the sound or picture The following are not malfunctions. • The television may make a creaking sound if the temperature of the room or the temperature of the inside of the television changes. If there is no problem with the screen or sound, then there is no need to worry. • There lamp may make a noise when it blows, but this is not dangerous. • The lamp may make a noise when the power is turned on and a picture is displayed on the screen. This noise is caused when the mercury which is inside the lamp is heated and is not a malfunction. • The still parts of the picture may remain on the screen. This is a characteristic of ILA elements and not a malfunction. The picture will disappear over time. • The operation of this television is not guaranteed below 0°C. If the power is turned on when the temperature is below 0°C, the picture may be disturbed. Use the television when the temperature is 0°C or higher. • Although the D-ILA hologram element is manufactured with high-precision technology, please understand that some pixels may be lost or permanently displayed. • There is a cooling fan built-in to the television. Please understand that this fan will make some noise when the television is being used and while cooling. • Although the picture may be temporarily disturbed and noise may be seen on the screen if the power is turned on immediately after it has been turned off, this is not a malfunction. If the POWER LED and/or the ON TIMER LED on the front panel of the television are blinking, there is a problem with the television. Refer to the table below to check the condition. If you think that there is a problem, contact the JVC Service Center where you purchased the television. How the LED indicators are blinking Trouble The ON TIMER LED and POWER LED are blinking alternately. It is possible that the lamp has not been installed correctly, or it may be a malfunction. The ON TIMER LED and POWER LED are lit at the same time. It may be a malfunction. The ON TIMER LED is blinking. It may be a malfunction. The POWER LED is blinking. It may be a malfunction. When you try to turn the power on, the cooling mode is entered and the power does not turn on. The lamp may be blown. Replace it with a new lamp. The filter unit may not be installed correctly. The filter unit may be ...