Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
15. OVERLOADING Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 16. OBJECT AND LIQUID ENTRY Never push objects of any kind through openings in the product as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid on the product. 17. OUTDOORANTENNAGROUNDING If an outside antenna is connected to the product, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electric Code,ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge product, size of grounding conductors, location of antenna discharge product, connection to grounding electrodes, and requirements for grounding electrodes. 18. SERVICING Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 19. REPLACEMENT PARTS When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards. 20. SAFETY CHECK Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 21. WALL OR CEILING MOUNTING The product should be mounted to a wall or ceiling only as recommended by the manufacturer. 22. DAMAGE REQUIRING SERVICE Unplug the product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally after installation by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. 23. HEAT The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. 24. NOTE TO CATV SYSTEM INSTALLER This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. e. If the product has been dropped or the cabinet has been damaged. f. When the product exhibits a distinct change in performance. ANTENNA LEAD IN WIRE GROUND CLAMP ELECTRIC SERVICE EQUIPMENT NEC-NATIONAL ELECTRICAL CODE GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) GROUNDING CONDUCTORS (NEC SECTION 810-21) (NEC ART 250, PART H) S2898A EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE WARNING: FOR CONTINUED SAFETY, REPLACE SAFETY CRITICAL COMPONENTS ONLY WITH MANUFACTURER'S RECOMMENDED PARTS (REFER TO SERVICE LITERATURE). 3 Identification of Controls Front Identification of Controls Front Back TV/AV MENU CH CH VOL VOL MENU TV/AV Channel down Channel up Volume down Volume up Power button Remote sensor Indicator () 2 R L VIDEO )(MONO AUDIO AV2 input (VIDEO, AUDIO: L/MONO,R) DVD input Antenna input RF AV output (VIDEO, AUDIO: L,R) (VIDEO: Y,C,C,B R AUDIO:L/MONO,R) S-VIDEO input L/MONOL VIDEO VIDEO ()1 YUV AUDIO AUDIO-SVIDEO R R Y CB CR 4 Identification of Controls Identification of Controls Remote control TV/AV CCD DSP MUTE 1 2 3 4 5 6 7 8 9 0 SCAN P CH+ MENU CH- V-V+ Power on/Standby Direct channel select Open the menu Volume down Program scan Return to previous channel Sound mute Recall on-screen display TV/VIDEO input select Closed Caption decoder channel select Picture mode select Parental Control Picture adjust Sleep timer Volume up Select higher program Select lower program STEREO To switch between STEREO, SAP or MONO 5 Antenna connection CABLE TV (CATV) CONNECTION A75-ohm coaxial cable connector is built into the set for easy hookup. When connecting the 75-ohm coaxial cable to the set, screw the 75-ohm cable to theANT. Terminal. Some cable TV companies offer "premium pay channels". Since the signals of these premium pay channels are scrambled, a cable TV converter/descrambler is generally provided to the subscriber by the cable TV company. This converter/descrambler is necessary for normal viewing of the scrambled channels. For more specific instructions on installing cable TV, c...
Эта инструкция также подходит к моделям:Телевизоры - TTM-2401 (445.43 kb)
Телевизоры - TTM-2401 (445.43 kb)
Телевизоры - TTM-2401 (445.43 kb)
Телевизоры - TTM-2401 (445.43 kb)