Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Thus, after exiting the menu, the channel will then be skipped when you select programs with the Channel up/down button. If you want to skip other unwanted channels, repeat steps above to change the channel number. Note: you can select the skipped channel by pressing the direct channel select buttons. To restore a skipped channel Use direct channel select buttons (0-9) to select the channel you want to restore. Enter into Search menu, press CH-or CH+ to select Skip, p ress V-or V+ to select Skip Off. Manual Fine Tuning Fine tuning is not necessary under normal conditions. However, in some areas where there is interference, some adjustment may be necessary for better picture and sound. To fine tune a channel: 1 1 Select the channel you want to fine-tune. 2 2 Enter into Search menu, p ress CH-or CH+ to select Fine Tune , then p ress and hold V-or V+ to fine tune the channel until the best possible picture and sound are achieved. (Press V-to fine-tune downward and V+ to fine-tune upward. The AFT function will be set to OFF mode automatically) Search Signal Input Channel Skip Auto Search Fine tune Air 28 Off Press V+ -5 If Fine Tuning makes the picture and sound of a channel poor, you can correct this by usingAFT. 1 Enter into Search menu, press CH-to select AFT. 2 Press V-or V+ to select AFT On. 13 Search Channel Skip Auto Search Fine tune 28 Off Press V+ -5 AFT On Channel selection Channel selection You can select desired TV programs by one of the following methods. Use Direct Channel Select buttons TV/AV CCD DSP MUTE 1 2 3 4 5 6 7 8 9 0 SCAN P CH+ MENUV- CH- V+ STEREO AIR Mode Direct Channel Selection When the Signal Input menu option in Search menu is in the Air position, all channels can be selected by directly entering Direct channel the channel number. select buttons CATV Mode Direct Channel Selection When the Signal Input menu option in Search menu is in the CATV position, channels can be selected as follows: DSP Method 1: Directly enter the channel number and wait for a few moments. Method 2: 1-9: Press “0” twice, then 1-9 as needed. For example, to select channel 2, press “002”. 10-99: Press “0”, then the remaining 2 digits. For example, to select channel 12, press “012”. 100-125: Press the 3 digits in order. For example, to select channel 120, press “120”. CH+ Use Channel up/down buttons Press CH+ button, the channel number increases; Press CH-button, the channel number decreases. CH- Use previous channel button Press button to switch between the current channel and the previous one. Notes: Use DSP button to know the current channel number Press DSP button to display the 12 ST SAP current state of the TV. If the TV is in program viewing mode, it will display the current channel number, sound mode and remaining sleep time (if set). Sleep 22 To scan programs Press SCAN button and the TV will scan the channels from the current channel to higher channels one by one. Every program will be displayed for about one second and then the TV will continue scanning. Press SCAN button again and the TV will stop at the displayed program. 14 Picture adjustment Picture adjustment To select the picture mode Menu control buttons DSP P TV/AV CCD DSP MUTE 1 2 3 4 5 6 7 8 9 0 SCAN P CH+ MENU CH- V-V+ STEREO You can select the picture quality instantly among three preset Standardmodes and one user-set mode. Dynamic Press P button to select the desired picture quality. Standard, Mild Dynamic, Mild and User (user-set) can be selected cyclically. User Mode Picture quality Standard Display normal pictures Dynamic Display dynamic pictures Mild Display soft pictures User The picture quality you set Picture adjustment 1 Press MENU button to display the Picture menu. 2 Press CH+ or CH-to select item. 3 Press V+ or V-to adjust the level. Or you can also make use of Brightness Contrast Color Sharpness Tint Picture button to adjust picture. Every time you press button, one picture adjustment menu bar will appear. Then make use of V+ or V-button to adjust the level. Item VV+ Brightness darker lighter Contrast weaker stronger Color paler deeper Sharpness softer sharper *Tint purplish greenish Notes: * To exit the menu, press button or DSP The adjusted level is stored in the User position. repeatedly press button.MENU 15 Sound controls Sound controls Adjusting volume MUTE V- V+ TV/AV CCD DSP MUTE 1 2 3 4 5 6 7 8 9 0 SCAN P CH+ MENU CH- V-V+ STEREO STEREO 1 Use Volume up/down button Press V-button, the volume decreases; Press V+ button, the volume increases. 2 Make use of Sound menu to adjust volume Press MENU twice to display Sound menu, then make use of V+/-button to adjust the level. Volume Sound 3 Use MUTE button. If you want to mute the sound, press MUTE button on the remote. To resume the sound, press the button again. To select MTS (Multi-channel TV Sound)(option) Stereo (If the program is STEREO) Mono SAP (If the program is SAP) Mono SAP (If the program is STEREO & SAP) Mono Stereo SAP: second audio program STEREO: stereo audio M...
Эта инструкция также подходит к моделям:Телевизоры - TTM-2401 (445.43 kb)
Телевизоры - TTM-2401 (445.43 kb)
Телевизоры - TTM-2401 (445.43 kb)
Телевизоры - TTM-2401 (445.43 kb)