Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
page 44). •• Some PC models cannot be connected to this TV. •• An adapter is not needed for computers with a compatible mini D-sub15-pin terminal. •• Depending on the DVD’s title and the specifications of the PC on which you are playing the DVD-Video, some scenes may be skipped or you may not be able to pause during multi-angle scenes. • Signal names for mini D-sub 15-pin connector Pin No. Signal name Pin No. Signal name Pin No. Signal name 1 R 6 Ground 11 Reserved 2 G 7 Ground 12 SDA 3 B 8 Ground 13 H-sync 4 Reserved 9 5V 14 V-sync 5 Reserved 10 Ground 15 SCL To connect a PC to the HDMI terminal on the TV: When connecting a PC to the HDMI terminal on the TV, use an HDMI-to DVI adapter cable and analog audio cables. If connecting a PC with an HDMI terminal, use an HDMI cable (type A connector). Separate analog cables are not necessary (. page 16). PC audio output PC audio cable TV back panel Computer The HDMI input can accept and display VGA, SVGA, XGA, WXGA, SXGA, 480i (60Hz), 480p (60Hz), 720p (60Hz), 1080i (60Hz), and 1080p (24Hz/60Hz) signal formats. For detailed signal specifications, see page 57. .................................................. .............................................. 20 Installing the remote control batteries 1. Remove the battery cover from the back of the remote control. Squeeze tab and lift cover. 2. Install two “AAA” size batteries, making sure to match the + and – signs on the batteries to the signs on the battery compartment. 3. Reinsert the battery cover in the remote control until the tab snaps. Caution: Batteries must not be exposed to excessive heat such as sunshine, fire or the like. Note: •• Be sure to use AAA size batteries. •• Dispose of batteries in a designated disposal area. •• Batteries should always be disposed of with the environment in mind. Always dispose of batteries in accordance with applicable laws and regulations. •• If the remote control does not operate correctly, or if the operating range becomes reduced, replace batteries with new ones. •• When necessary to replace batteries in the remote control, always replace both batteries with new ones. Never mix battery types or use new and used batteries in combination. •• Always remove batteries from the remote control if they are dead or if the remote control is not to be used for an extended period of time. This will prevent battery acid from leaking into the battery compartment. Remote control effective range For optimum performance, aim the remote control directly at the TV and make sure there is no obstruction between the remote control and the TV. 16.4 ft (5m) Point remote control toward remote sensor on front of TV. Chapter 3: Using the remote control .................................................. .............................................. Chapter 3: Using the remote control 21 Learning about the remote control The buttons used for operating the TV only are described here. Note: The error message “NOT AVAILABLE” may appear if you press a key for a function that is not available. 1. POWER turns the TV on and off. When the TV is on, the green LED indicator on the TV front will be illuminated. 2. PIC SIZE cycles through the picture sizes: Natural, TheaterWide 1/2/3, Full, 4:3 HD, Native and Dot by Dot (. page 34). 3. PIC MODE selects the picture mode (. page 36). 4. INPUT selects the video input source (. page 29). 5. SLEEP accesses the sleep timer (. page 48). 6. FREEZE freezes the picture. Press again to restore the moving picture (. page 36). 7. Channel Numbers (0–9, –/100) directly tune channels. The button is used to tune digital channels (. page 33) or to edit the Favorites List (. page 30). 8. FAV BROWSER accesses the Favorites List in the Channel Brower™ (. page 30). 9. RECALL displays TV status information (. page 50). 10. CH pq cycles through programmed channels when no menu is on-screen (. page 25). 11. C.CAPTION accesses the closed caption (. page 38). 12. MUTE reduces or turns off the sound (. page 38). 13. VOL + – adjusts the volume level. 14. INFO displays TV status information as well as program details, when available (. page 50). 15. EXIT closes on-screen menus. 16. ENTER activates highlighted items in the main menu system. 17. CH RTN returns to the last viewed channel or source (. page 33). 18. Arrow buttons (pqtu) When a menu is on-screen, these buttons select or adjust programming menus. (Also see t / u .) 19. t / u While watching TV, these buttons open the Channel Browser™ and tune to the previous/next channel in the channel history (. page 31). (Also see “Arrow buttons.”) 20. MENU accesses the main TV menu system (. pages 22 and 23). 21. STOP Stops the tape or DVD. 22. PLAY Begins playback of a tape or DVD. 23. SKIP Skips forward to locate later DVD chapters. 24. FF Fast-forwards the tape or DVD.(Press during play mode to view the picture moving rapidly forward.) 25. EJECT Eject the tape or DVD. 26. PAUSE Press during play or record mode to pause the picture ; press aga...
Эта инструкция также подходит к моделям:Телевизоры - 40E200U2 (6.42 mb)