Оценок - 3, средний балл: 3.3
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
It is useful at night. N To use the volume control on the source device connected to the TV as shown below, set Auto Volume to Off on the TV. Otherwise, a change to the volume control of the source device may not be applied. ► English ■ Reset Sound (OK / Cancel) Reset all sound settings to the factory defaults. 4 ► English □ Selecting the Sound Mode © DUAL I-II —— ENTERE When you set to Dual I-II, the current sound mode is displayed on the screen. Audio Type Dual I-II Default A2 Stereo Mono Mono Automatic change Stereo Stereo ^ Mono Dual Dual I ^ Dual II Dual I NICAM Stereo Mono Mono Automatic change Stereo Mono ^ Stereo Dual Mono ^ Dual I n Dual II ^ Dual I ► N If the stereo signal is weak and an automatic switching, occurs, then switch to the mono. N Only activated in stereo sound signal. N Only available when the Source is set to TV. English A □ ■ Setting the Network Network Settings For LCD 550 series and above Set the network connection to use AllShare™ and perform software upgrade. ■ Network Status © MENU m — Network — Network Status — ENTERE You can check the current network and Internet status. ■ AllShare Settings O MENU m ^ Network ^ AllShare Settings ^ ENTER E Selects whether to use the call arrivals text message contents, and schedules set on the network. For details on set up options, refer to the “AllShare™” instructions. ► English □ Connecting to a Wired Network You can attach your TV to your LAN using cable in three ways: • You can attach your TV to your LAN by connecting the LAN port on the back of your TV to an external modem using a LAN cable. See the diagram below. A ► English A • You can attach your TV to your LAN by connecting the LAN port on the back of your TV to a IP Sharer which is connected to an external modem. Use LAN cable for the connection. See the diagram below. ► English • Depending on how your network is configured, you may be able to attach your TV to your LAN by connecting the LAN port on the back of your TV directly to a network wall outlet using a LAN cable. See the diagram below. Note that the wall outlet is attached to a modem or router elsewhere in your house. TV Rear Panel ► English < • If you have a Dynamic Network, you should use an ADSL modem or router that supports Dynamic Host Configuration Protocol (DHCP). Modems and routers that support DHCP automatically provide the IP address, subnet mask, gateway, and DNS values your TV needs to access the Internet so you do not have to enter them manually. Most home networks are Dynamic Networks. Some networks require a Static IP address. If your network requires a Static IP address, you must enter the IP address, subnet mask, gateway, and DNS values manually on your TV’s Cable Setup Screen when you set up the network connection. To get the IP address, subnet mask, gateway, and DNS values, contact your Internet Service Provider (ISP). If you have a Windows computer, you can also get these values through your computer. N You can use ADSL modems that support DHCP if your network requires a Static IP address. ADSL modems that support DHCP also let you use Static IP addresses. N A network speed of lower than 10 Mbps is not supported. ► English A ■ Network Setup (Auto) Use the Automatic Network Setup when connecting your TV to a network that supports DHCP. To set up your TV’s cable network connection automatically, follow these steps: How to set up automatically 1. Go to Network Settings screen. To enter it, follow the directions of Network Settings. 2. Select the Wired. 3. The network connection screen appears, and network setting is done. Network Settings Select a network connection type. ► Wired -1 _jJ Wireless (general) HWPS(PBC)H One Foot Connection Connect to the network using a LAN cable. Please make sure that the LAN cable is connected. E Enter e Exit Move English 2 B If it fails to set automatically, check the connection of LAN port. If you cannot find network connection values or if you want to set connection manually, set it to Manual. Refer to following “How to set up manually”. English Network bettings Wired network and Internet connection completed. MAC Address IP Address Subnet Mask Gateway DNS Server à 1 00:40:30:30:20:10 192.168.10.21 255.255.255.0 192.168.10.1 203.248.252.2 Internet is connected successfully. If you have a problem with using Internet service, contact your Internet service provider. Previous <► Move И Enter 'O Return ► A ■ Network Setup (Manual) Use the Manual Network Setup when connecting your TV to a network that requires a Static IP address. Getting the Network Connection Values To get the Network connection values on most Windows computers, follow these steps: 1. Right click the Network icon on the bottom right of the screen. 2. In the pop-up menu that appears, click Status. 3. On the dialog that appears, click the Support tab. 4. On the Support Tab, click the Details button. The...
Эта инструкция также подходит к моделям:Телевизоры - LA32D450G1W (6.3 mb)
Телевизоры - LA32D550K7W (6.3 mb)
Телевизоры - LA40D550K7W (6.3 mb)
Телевизоры - LA46D550K7W (6.3 mb)