Оценок - 2, средний балл: 4
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Press trn a (New) button to search the digital channels. When scanning has finished, a channel is updated in the channel list. - When selecting Antenna ^ Air: Channel, Frequency, Bandwidth - When selecting Antenna ^ Cable: Frequency, Modulation, Symbol Rate - When selecting Antenna ^ Satellite: Satellite, Channel for LCD 570 series ► English < • Analogue Channel Tuning : Scans for an analogue channel. Press tip a (New) button to search the digital channels by adjusting the Programme, Colour System, Sound System, Channel, Search. N Channel mode - P (programme mode): When tuning is complete, the broadcasting stations in your area have been assigned to position numbers from P0 to P99. You can select a channel by entering the position number in this mode. - C (aerial channel mode) / S (cable channel mode): These two modes allow you to select a channel by entering the assigned number for each aerial broadcasting station or cable channel. ► English When Antenna Source is set to Satellite for LCD 570 series • Transponder: Selects the transponder using the up/down buttons. • Scan Mode (All Channels / Free Channels Only): Selects either free or all channels to store. • Network Search (Disable / Enable): Enable / Disable network search using the up/down buttons. • Signal Quality: Display the current status of broadcasting signal. N Information on a satellite and its transponder is subject to change depending on the broadcasting conditions. N When setting is completed, move to Search and press the ENTER E button. Channel scan is started. ► English for LCD 570 series ■ Satellite System The PIN input screen appears. Enter your 4 digit PIN number. Satellite System is available when Antenna is set to Satellite. Before running Auto Store, set Satellite System. Then channel scan is run normally. • Satellite Selection: You can choose the satellites for this TV. N This function is available when Antenna is set to Satellite. • LNB Power (Off / On): Enables or disables the power supply for the LNB. • LNB Settings: Configures the outdoor equipment. 4 Satellite: Selects the satellite for receiving digital broadcasts. ► Transponder: Selects a transponder from the list or adds a new transponder. DiSEqC Mode: Selects DiSEqC mode for the selected LNB. Lower LNB Oscillators: Sets the LNB oscillators to a lower frequency. English 4 Upper LNB Oscillators: Sets the LNB oscillators to a higher frequency. Tone 22 kHz (Off / On / Auto): Selects the Tone 22 kHz depending on the LNB type. For a universal LNB it should be Auto. Signal Quality: Display the current status of broadcasting signal. • SatCR/Unicable Settings N It is available when LNB Power is set to On. N During using this function, the sound will be mute temporarily. SatCR/Unicable Settings(On / Off): Enable or disable single cable installation support. Slot Number: Select the SatCR user slot number for this receiver. Choose it in the range of 1 to 8. ► English 4 Slot Frequency: Enter the appropriate frequency to receive the signal from SatCR. N It has the entire range from 950MHz to 2150NHz. The predefined values are 1210MHz, 1420MHz, 1680MHz, 2040MHz. Detect Slot Frequency: Detect the signal frequency automatically for the selected slot number. Verify Slot Frequency: Verify that the entered frequency corresponds to the selected slot number. ► English • Positioner Settings: Configures the antenna positioner. Positioner (On / Off): Enables or disables the positioned control. Positioner Type (USALS / DiSEqC 1.2): Sets the positioned type between DiSEqC 1.2 and USALS(Universal Satellite Automatic Location System). - My Longitude: Sets the longitude for my location. - My Latitude: Sets the latitude for my location. - Satellite Longitude Settings: Sets the longitude of user defined satellites. 4 ► English 4 User Mode: Sets the position of satellite antenna according to each satellite. If you store the current position of satellite antenna according to a certain satellite, when the signal of that satellite is needed, the satellite antenna can be moved to pre-populated position. - Satellite: Selects the satellite to set the position for. - Transponder: Selects a transponder from the list for signal reception. - Moving Mode: Selects the movement mode between discrete and continuous movement. - Step Size: Adjusts the step size degrees for the antenna rotation. Step Size is available when Moving Mode is set to Step. - Go to Stored Position: Rotates the antenna to the stored satellite position. ► English < - Antenna Position: Adjusts and stores the antenna position for the selected satellite. - Store Current Position: Stores current position as the selected positioner limit. - Signal Quality: Display the current status of broadcasting signal. Installer Mode: Sets limits to the scope of movement of satellite antenna or reset the position. Generally, installation guide uses this function. - Limit Position (East / West...
Эта инструкция также подходит к моделям:Телевизоры - LA32D450G1W (6.3 mb)
Телевизоры - LA40D550K7W (6.3 mb)
Телевизоры - LA46D550K7W (6.3 mb)
Телевизоры - LE19D450G1W (6.3 mb)