Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
• On-screen displays appear each time you change a function. • This is part of normal TV operation. • You cannot program the TV to turn on automatically. • The TV may be locked. • The clock may not be set. • There is no sound even when the volume is turned up. • Check to see if the MUTE button is on. • The TV’s “Listen to:” setting may be set to SAP. • Check that “TV Speakers” setting is ON in the Audio/Video menu. • Check audio source in Device Menu. • You have forgotten your lock passcode. • See Appendix A, Bypassing the V-Chip Lock. • PIP does not display a picture. • Make sure the V-Chip lock is off. • Not all inputs can be displayed as a PIP. • The sound does not match the screen picture. • The TV’s “Listen to:” setting may be set to SAP. • If using stereo or A/V receiver speakers, check input selection on the stereo or A/V receiver. • If using stereo or A/V receiver, check that AUDIO of MONITOR OUTPUT on TV’s back panel is connected to the A/V receiver. • NetCommand™ is setup incorrectly. • •There is a large black or gray rectangle on the screen. • The TV closed captioning has been set to “text” mode in the Captions menu. Turn off because there is no text information being broadcast. •You cannot see a picture when you play a VCR tape. • Display the Device Selection menu and select the correct VCR. • Check your VCRs owner’s guide for further trouble shooting. • V-Chip is not working • Make sure that V-Chip is On. • If V-Chip Time is currently set to disable the V-Chip lock, the V-Chip will not block programming. 82 Problem Possible Solution • The TV will not turn on after being plugged in. • If green light on front panel is blinking, please wait for at least one minute for light to turn off, then try to power on again. • TV functions do not respond to the remote control • Use the System Reset button as explained below. or to front panel control and the TV will not power off. • When viewing a stopped VCR, white lines are rolling • Turn off video mute for the VCR. on the screen. • Begin playing the tape. • Change the VCR input to the antenna input. • TV turned itself Off and the light on the Front Panel started • Momentary power fluctuation caused the TV to turn Off to flashing prevent damage. Wait for the green light to stop flashing and turn On again. If the TV does not stay turned On, use the System Reset button. If this happens frequently, obtain an AC line in power conditioner / surge protector. Using The System Reset Button: If the TV doesn’t respond to either the remote control or the front panel controls will not power off, press the SYSTEM RESET button on the front panel with a pointed item like the point of a ball point pen or end tip of a paperclip. The TV will turn off and the TIMER light will flash quickly for about one minute. When the TIMER light stops flashing, you may turn on the TV again. The changes you made while the TV was on before you used the SYSTEM RESET button may be cancelled, however, the changes you made previously are not cancelled. Only those changes since the last power on may be lost when the system reset button is pressed. All other settings are retained. Appendix G: Troubleshooting 83 Appendix H: On Screen Information Display On Screen Information Displays When you turn on the TV, change Devices, change Channels or when you press the INFO button on the remote control the TV will display the current status. Below are the most common displays; please note that seldom or never do all of the different status indicators appear at the same time. Analog Antenna or Devices 1. Antenna or Device being viewed 2. Analog channel being received: If antenna being viewed Ant-A 003 WBAT PIP A003 3. Analog channel name (only if manually 480i Standard programmed) Stereo SAP 4. Signal Type being received TV-PG DLSV Possible: SQV2 Ant-A, Ant-B or Input 1-5 – 480i Component 1 or 2 – 480i or 480p Monday 11:00 AM Input-DTV – 480i, 480p, 1080i Sleep Timer: 30 5. Screen format being used Possible: 480i signals – Standard, Expand, Zoom, Stretch, Narrow 480p signals – Standard, Narrow 1080i signals - Standard 1234511786910 6. Stereo and/or SAP being broadcast 7. V-Chip Ratings 8. Channel in SuperQuickView bank 2 9. Day and Time 10. Sleep Timer remaining time 11. PIP source and channel 35 Ant-DTV 42.01 WBAT-DT 12 Digital Antenna HD Standard English 1. Digital Major and Sub channel number 4 TV-PG DLSV 2. Digital Channel Name (only if broadcast) SQV2 3. Signal Type being broadcast/received Possible: SD 4:3, SD 16:9 or HD Monday 11:00 AM 4. Screen format being used Sleep Timer: 30 Possible: SD 4:3 - Standard, Expand, Narrow SD 16:9 or HD - Standard 5. Language being broadcast Digital IEEE 1394 Device DVHS 1. Status of D-VHS VCR or IEEE 1394 device HD Standard 2. Counter of D-VHS VCR English 3. Media type in D-VHS VCR TV-PG DLSV 4. Special message line 13 Play 01:20:15 2 (shows only when a special message is needed; DVHS may be seen with Analog signals) Monday 11:00 AM Sleep Timer: 30 4 Special Message...
Эта инструкция также подходит к моделям:Телевизоры - WS-48511 (2.33 mb)
Телевизоры - WS-48511 (2.33 mb)
Телевизоры - WS-55711 (2.33 mb)
Телевизоры - WS-55511 (2.33 mb)