Оценок - 3, средний балл: 3.7 ( )

Производитель: Hitachi Размер: 5.29 mb Название файла: Язык инструкции:

2 Connecting External Devices & NetCommand® Setup16 Wall Outlet Cable or Cable Box17 CableCARD™ Technology18 Single Lead Antenna19 Separate UHF and VHF Antennas 19 VCR Video and Audio to an Antenna or Wall Outlet Cable20 VCR Video and Audio to a Cable Box21 A/V Receiver or Stereo System22 Satellite Receiver or Other Device with S-Video22 DVD Player with Component Video23 Computer with a PC Monitor Output23 DTV Receiver with Component Video24 with RGB, HV Video 25 M-Link Control, RS-232 Connection26 HDMI Device26 DVI Device26 IR Emitter NetCommand®27 Compatible IEEE 1394 Devices28 Helpful Hints30 Connecting External Devices & NetCommand® Setup NetCommand is able to control many current audio and video devices by sending remote control signals from the TV to each device through IR emitters. Additionally, it is also able to learn the remote control signals used by most audio video devices not already in the TV’s memory. NetCommand can automatically switch the TV and compatible or learned Audio/Video (A/V) Receivers to the correct input used with each device. It is important that the inputs on the TV and A/V receiver back panels match the NetCommand setup that is displayed on-screen. To simplify the installation of NetCommand, there is a step-by-step on-screen NetCommand Setup procedure in this chapter, which details the type and brands of devices you are connecting to the TV. The NetCommand Setup also assigns preset TV and A/V receiver inputs for each device. You should connect each device to the TV input (both audio and video) and to the A/V receiver (audio) as shown in the figure below. AVReceiverTVDevicetobeconnectedstereoand/ordigitalaudiocablesvideoandstereoaudiocablesstereoanddigitalaudiocables IREmitters The following charts show which preset inputs you should use on the TV and A/V receiver. Chart 1 shows TV inputs. Chart 2 shows the A/V receiver inputs used by A/V receiver models already known by NetCommand. Chart 1 Device Audio and Video Outputs to TV Inputs Cable for CableCARD™ Service ANT-1 Antenna/Cable (digital/analog) ANT-1 if primary viewing source, ANT-2 if secondary viewing source Cable box ANT-2 VCR Input-1 Satellite Receiver (DBS) Input-2 Camcorder Input-3 (on front panel) DVD Player Component-1 ModelM-VR800& M-VR1000ModelM-VR900& M-VR700ModelLifestyle®28ModelAVR-2700ModelDTR-9.1ModelVR-2080ModelSR8200ModelVSX-D557ModelVSX-49TXModelRSX-1065ModelSTR-DE825ModelRV-X2095ModelRX-V2200DeviceAudioOutputtoAVReceiverInputsbyNameVCRVCR1VCRVCRVCR-1Video1Video1VCR1VCR/TapeVCR1/DVRVideo2Video1VCR1VCR1SatelliteReceiverAuxCable/DBSAUXCDVideo3Video3DSSCDSATVideo4TV/DBSTV/DBSD-TV/LDDVDPlayerDVDDVD(built-in)DVDVDPDVDVideo4DVDLD/SATDVD/LDVideo5TAPE/MDCDDVDTVMonitorOutput(&DigitalAudio) TVTVTVTV/DBSVideo4Video4TVDVD/TVTVVideo1DVD/LDDVD/LDCBL/SATChart2Mitsubishi1Mitsubishi2BoseDenonIntegraKenwoodMarantzPioneer1Pioneer2RotelSonyYamaha1Yamaha2 After using NetCommand Setup, you may go to the NetCommand menu at any time to change the inputs you used for connecting each device, custom name devices, add devices not included in the presets above or delete devices no longer used. See Edit NetCommand. See Helpful Hints, at the end of this chapter for additional information on device setup. Connecting a Wall Outlet Cable or Cable Box Cable Box (compatible with PIP/POP) Figure 2 3 coaxial cables and one two-way RF splitter are required. These are not included with the TV. It is very important to connect the incoming cable for your primary viewing source to ANT-1, especially for CableCARD™ use. 1. Connect the incoming cable to IN on an RF splitter. 2. Connect one coaxial cable from OUT on the RF splitter to ANT-1 MAIN on the TV back panel. 3. Connect one coaxial cable from OUT on the RF splitter to IN on the cable box. 4. Connect one coaxial cable from OUT on the cable box to ANT-2 AUX on the TV back panel. Wall Outlet Cable (can be used with a CableCARD™) Figure 1 It is very important to connect the incoming cable for your primary viewing source to ANT-1, especially for CableCARD™ use. 1. Connect the primary incoming coaxial lead cable to ANT-1 MAIN on the TV back panel. 2. For an optional secondary antenna source, connect an antenna (or cable) to ANT-2 AUX. 3. If you have subscribed to a CableCARD™ service, the CableCARD can now be inserted into the CableCARD SLOT. Using a phillips screwdriver, remove the CableCARD cover screws. Insert the CableCARD, then replace the cover and screws. Additional CableCARD information is on page 18. CableBoxbackpanelsectionIncomingCableINOUT INOUTOUTTWOWAYSPLITTER1.4.2.3.3.4.2. IREMITTERNetCommandRDVIAnalogAudioDTV/ CABLE/ VHF/ UHFANT-2AUXANT-1MAINM-LINKCONTROL/ RS-232CHDMIM-LINKLR TVbackpanelsection CableCARDTMSLOT(coverremoved) 3. DIGITALAUDIOIREMITTERNetCommandRDVIAnalogAudioDTV/ CABLE/ VHF/ UHFANT-2AUXANT-1MAINM-LINKCONTROL/ RS-232CHDMIM-LINKLR TVbackpanelsectionCARDTOPCableCARDSLOTTM1.PrimaryWallOutletCable 2.OptionalSecondaryAntennaorCable Figure 2. Connecting a Cable Box Note: Net C...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: