Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Proceed in the same way to program the other functions. The programming menu can only be accessed when the machine is on and shows this display. 1 Press the “ ” button to access programming 2 The first page is displayed. 3 Press the “ ” button to scroll the functions pages until the display contrast function is displayed. 50 ENGLISH 4 Press the “ ” and “ ” buttons to increase or decrease the value of the function. Yellow 5 When the display value is changed, the “OK” message appears. Press the “ ” button to confirm the change. 6 Press the “ ” button to exit the programming mode. Note: The machine will automatically exit the programming mode if you do not push any button for 3 minutes. The function’s values that were changed but not confirmed won’t be saved. ENGLISH 51 5151 This machine is equipped with a colour-coded system to make your understanding of the display signals easier. The icons are colour-coded according to the traffic light principle. MEANING OF THE DISPLAY SYMBOLS Ready Signals (Green Colour) The machine is ready to brew products. The machine is ready to brew pre-ground coffee. Hot water dispensing. Steam dispensing. The machine is brewing one cup of espresso. The machine is brewing one cup of Coffee. The machine is brewing two cups of espresso. The machine is brewing two cups of Coffee. The machine is programming the amount of coffee to be brewed. 52 ENGLISH Ready Signals (Green Colour) Coffee brewing using pre-ground coffee in progress. Warning Signals ( Yellow Colour) The machine is heating-up to brew beverages or dispense hot water/steam. The machine performs the rinsing cycle. Wait until the machine has comple- ted the cycle. The machine needs the “INTENZA+” water filter to be replaced. The brew group is being reset due to machine reset. Refill the coffee bean hopper with coff ee beans. Prime the circuit. The machine needs to be descaled. Press the “ ” button to start the de- scaling process. Follow the steps described in the “Descaling” chapter of this manual. If you want to descale later, press the “ ” button to continue using the machine. Please note that not descaling your machine will ultimately make it stop wor- king properly. In this case repair is NOT covered under your warranty. ENGLISH 53 5353 Warning Signals (Red Colour) Completely insert the drip tray with the coffee grounds drawer into the ma- chine and close the service door. Fill the coffee bean hopper. The brew group must be inserted into the machine. Empty the coffee grounds drawer. Fill the water tank. ExxTurn off the machine. After 30 seconds, turn it on again. Try this 2 or 3 times. If the machine does not start, contact the Philips SAECO hotline in your country and communicate the the Error-code which you see on the display. You can find its contact details in the warranty booklet by-packed separately or on 54 ENGLISH TROUBLESHOOTING This chapter summarizes the most common problems you could en- counter with your machine. If you are unable to solve the problem with the information below, visit for a list of frequently asked questions or contact the Philips Saeco hotline in your country. You find its contact details in the warranty booklet by-packed separately or on Machine actions Causes Solutions The machine does not switch on. The machine is not connected to the electric network , or the main switch is in O position. Connect the machine to the electric network , turn the main switch to I position The drip tray gets fi lled al- though no water is drained. Sometimes water is drained auto- matically by the machine into the drip tray to manage the rinsing of the circuits and ensure optimum machine performance. This is seen as normal machine behavior. The red icon is always displayed on the machine. The coffee grounds drawer was emptied with the machine off . The coffee grounds drawer must always be emptied with the machine on. Wait until the icon is display- ed before refitting the drawer. Coffee is not hot enough. The cups are cold. Preheat the cups with hot water. No hot water or steam is dispensed. The hole of the hot water / steam wand is clogged. Clean the hole of the steam wand using a pin. Make sure that the machine is off and cold before performing this operation. Coffee does not have enough crema. (See note) The blend is unsuitable, coff ee is not freshly roasted or the grind is too coarse. Change coffee blend or adjust the grinder as explained in chapter “Adjusting the ceramic coff ee grinder”. The machine takes a long time to warm up or the amount of water dispensed is too little. The machine circuit is clogged by limescale. Descale the machine. The brew group cannot be removed. The brew group is out of place. Turn the machine on. Close the ser- vice door. The brew group automati- cally returns to the initial position. The coffee grounds drawer is inserted. Remove the coffee grounds drawer before removing the brew group. ENGLISH 55 5555...