Оценок - 3, средний балл: 4.7 ( )

Производитель: Hitachi Размер: 8.25 mb Название файла: Язык инструкции:

As time passes, this system will become broadly supported by most cable providers. The CableCARD system is “unidirectional” which means your cable provider can send updates to the access card and TV, however, the TV cannot send back signals such as requests for Video-On-Demand or Pay-per-View programs by remote control. Digital cable channels authorized by the CableCARD will be available on the Firewire® IEEE 1394 network and can be shared by other products on the network. Some digital channels or programs may not be copied or recorded because of copy restriction limits set by the content owners or copyright holders. The digital television is capable of receiving analog basic, digital basic, and digital premium cable television programming by direct connection to a cable system providing such programming. A security card (CableCARD) provided by your cable operator is required to view encrypted digital programming. Certain advanced and interactive digital cable services, such as video-on-demand, a cable operator’s enhanced program guide, and data-enhanced television services, may require the use of a set-top box. For more information, call your local cable operator. Please see page 19 for instructions on inserting the CableCARD. Using a CableCARD™ After inserting a CableCARD into the TV back panel CableCARD slot and powering On the TV, the initialization process begins. An initial screen will automatically display for a few minutes, with information that your Cable Provider will need in order to start service. Please write down this information before calling your cable provider. Please call XYZ Cable at xxx-xxx-xxxx to activate cable service. They will need these numbers: Host ID X-XXX-XXX-XXX-XXX CableCARDTM ID: X-XXX-XXX-XXX-XXX See owner's manual for further information An example of an initial screen is shown here. Your screen will display specific information from your cable provider and may not look like this screen. If you were unable to record the information, you can press TV MENU on the remote and then enter the number 999 and the screen will re-display. You can also press DEVICE MENU when the CableCARD is the selected source and you will be able to select the startup application. IMPORTANT To use a CableCARD, the primary incoming cable must be connected to ANT-1 MAIN. MediaCommand™ and Memory Card Playback Warning: Some memory cards available on the market are not properly certified to follow the card type specifications noted below and cannot be used by the card reader. If you experience problems with the reading of your file, please transfer your files to a properly certified card. Memory Card Slots Inserting a memory card 1. Insert a card into a matching card slot on the front of the TV. Be sure to use the correct card slot. Card 1 accepts SmartMedia™. Card 2 accepts MultiMediaCard™ and SD Media Card. Card 3 accepts CompactFlash® and MicroDrive®. Card 4 accepts MEMORY STICK™ and Memory Stick Pro. Cards up to 1 GB, with a file format of FAT 16 (block size = 1024 or 2048) are supported. Normally the label side should be up, but if the card does not fit, try turning the card over and insert again. When properly inserted, the light next to the slot will light up. 2. Press DEVICE on the remote control to display the Device Selection Menu and then select the correct card slot from the list, using ADJUST . 3. The Media Dialog box (figure 1) will automatically display. Use the AUDIO button to switch from JPEG Picture Slide show setup to MP3 or WMA Audio Playlist setup or use the VIDEO button on the remote to switch from the MP3 or WMA Audio Playlist setup to JPEG Picture Slide show setup. Don’t pull the memory card out while it is playing. For Slideshow, press PLAY. For Thumbnails, press GUIDE. To redisplay this menu or to setup, press DEVICE MENU. For Playlist, press AUDIO. Figure 1. Media Dialog Box 4. On the remote control, press: PLAY: to start the slide show or play audio. GUIDE: to display the JPEG Thumbnail menu (Figure 2) or Audio track playlist (Figure 3) DEVICE MENU: to display the Media Setup menu (Figure 4). Remote Control Buttons for Controlling the Playback For JPEG Picture Slide show: PLAY: begins or resumes slide show playback PAUSE: pauses or resumes playback while in the automatic advance mode. FF: skips to the last slide on the page. REW: returns to the first slide on the page. FORMAT: single press rotates the slide 90.. Multiple presses continue to rotate the slide. STOP: Stop slide show, return to memory card screen. For MP3 or WMA Audio Playback PLAY: begins or resumes playlist playback. PAUSE: pauses or resumes playback. FF: skips to the last track/song on the page. REW: skips to the first track/song on the page. STOP: Stop playback and returns to memory card screen. Using the Picture Thumbnail Menu or Audio Playlist Menu For JPEG Picture Thumbnail Menu: Figure 2 1. Press GUIDE on the remote to display the JPEG picture Thumbnail menu. 2. Press ADJUST to move the highlight to dif...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: