Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
3 cables or Sync on green connections are incomplete or not compatible and will not work. 5. Connect the L (left) and R (right) audio cables from the DTV Receiver to Input-DTV AUDIO on the TV back panel. IREMITTERNetCommandRINPUT-1AUDIO2AUDIO/VIDEO1AUDIOL(MONO)RINPUT-2COMPONENT-1YPbPr(480i/480p/720p/1080i) Y/GPb/BPr/RCOMPONENT-2YPbPr(480i/480p/720p/1080i) INPUT-DTVYPbPr/RGBHV(480i/480p/720p/1080i) DTV/ CABLE/ VHF/ UHFANT-2AUXANT-1MAINDIGITALAUDIOPCVGA/SVGA/XGA/ 720p60HzPC- AUDIOPC- INPUTM-LINKCONTROL/ RS-232CHDMIM-LINKIEEE1394INPUT/OUTPUTVIDEOS-VIDEOMONITOROUTPUTLRVHCARDTOPCableCARDSLOTTM DTVReceiver(withRGBconnections) GRBS-VIDEOVCRCONTROLPHONEJACKRFREMOTEOUTTOTVCH3CH4CAUTIONRISKOFELECTRICALSHOCKDONOTOPENDIGITALAUDIOOUTWhiteRedIncomingAntennaorCable SATELLITEININFROMANTortoantenna, cableorsatelliteAUDIOLRHV1.1.4.4.5.4.5.3.3.2.2. TVbackpanelDVIAnalogAudioLRAUDIOL(MONO)RWhiteRedwhiteRed Figure 13. Connecting an External DTV Receiver with RGB Video Connections IMPORTANT See Appendix B for RGB, HV video signal compatibility information. For digital audio connections, see your DTV Receiver and A/V receiver Owner’s Guides. It may be necessary to obtain a VGA to RGB, HV adaptor cable. These are available at most computer stores and many electronic stores. Some of the adaptor cables have RCA type connector ends, others have BNC type ends and will require adaptors as shown on page 24. Connecting M-Link Control RS-232C Connection, or a HDMI or DVI Device M-Link Control RS-232C Connection Figure 14 A 9 pin RS-232C cable is required. This is not included with the TV. It may be available at your local electronics retailer As M-Link Control, connect to a Mitsubishi HD Receiver/Controller, like the HD-5000 or HD-6000. As RS-232C, connect to other external controllers. See mitsubish-tv.com for RS-232C command protocol. Connect a 9 pin RS-232C cable from the TV back panel to the M-Link or RS-232C on the external control device. DVI Device Figure 16 A DVI-to-HDMI cable or DVI/HDMI adaptor and HDMI cable and audio cables are required. These are not included with the TV. They may be available at your local electronics retailer. 1. Connect the DVI-to-HDMI cable (recommended) (or DVI/HDMI adaptor with an HDMI cable) from the DVI device’s back panel to the TV back panel. NOTE: If you are using a DVI/HDMI adaptor, it is important to connect the adaptor to the DVI side for best performance. 2. Connect a set of audio cables from AUDIO OUT on the the DVI device back panel to the DVI Analog Audio input on the TV back panel. The red cable connects to the R (right) channel, and the white cable connects to the L (left) channel. NOTE: The HDMI connection supports copy protection (HDCP). Some devices require connecting to an analog input first, in order to view on-screen menus and select DVI as the ouput. Please review your equipment instructions for DVI connectivity and compatibility. TVbackpanel(sectiondetail) IREMITTERNetCommandRDTV/ CABLE/ VHF/ UHFANT-2AUXANT-1MAINDIGITALAUDIOPCVGA/SVGA/XGA/ 720p60HzPC- AUDIOPC- INPUTM-LINKCONTROL/ RS-232CHDMIM-LINKIEEE1394INPUT/OUTPUTLRCARDTOPCableCARDSLOTTM ComputerwithMonitorOutput LRDVIAnalogAudio Figure 14. Connecting M-Link Control ...................................................................... DVIDEVICE ............ DVI-TO-HDMICABLE 2.2.1. IREMITTERNetCommandRDVIAnalogAudioINPUT-1AUDIO2AUDIO/VIDEO1AUDIOL(MONO)RINPUT-2COMPONENT-1YPbPr(480i/480p/720p/1080i) Y/GPb/BPr/RCOMPONENT-2YPbPr(480i/480p/720p/1080i) INPUT-DTVYPbPr/RGBHV(480i/480p/720p/1080i) DTV/ CABLE/ VHF/ UHFANT-2ANT-1DIGITALAUDIOPCVGA/SVGA/XGA/ 720p60HzPC- AUDIOPC- INPUTM-LINKCONTROL/ RS-232CHDMIM-LINKIEEE1394INPUT/OUTPUTVIDEOS-VIDEOMONITOROUTPUTLRVHCARDTOPCableCARDSLOTTM MAINAUX 1. LRDVIAnalogAudioLRDVIAnalogAudio HDMIM-LINK HDMI Device Figure 15 An HDMI to HDMI cable is required. This is not included with the TV. It may be available at your local electronics retailer Connect an HDMI cable from the TV back panel to the HDMI device output. HDMI devices provide video and audio through this cable, so no other connection is required. HD-6000Receiver TVbackpanel(sectiondetail) IREMITTERNetCommandRDTV/ CABLE/ VHF/ UHFANT-2AUXANT-1MAINDIGITALAUDIOPCVGA/SVGA/XGA/ 720p60HzPC- AUDIOPC- INPUTM-LINKCONTROL/ RS-232CHDMIM-LINKIEEE1394INPUT/OUTPUTLRCARDTOPCableCARDSLOTTMLRDVIAnalogAudio Figure 16. Connecting a DVI Device CAUTION: To ensure continued FCC compliance, the user must use a shielded video interface cable with bonded ferrite cores at both ends when using the PC input. Figure 15. Connecting HDMI Device Connecting the IR Emitter NetCommand® IR Emitter NetCommand® Figure 17 A quadruple IR Emitter cable is included with the TV. The emitters connected to these jacks are used by the NetCommand system to control other devices such as VCRs, DVD players, Cable boxes and Satellite receivers. 1. Connect the plug end of the supplied quadruple IR Emitter Cable to one of the IR Output NetCommand jacks on the TV back panel. 2. Run the cable for ea...
Эта инструкция также подходит к моделям:Телевизоры - WD-52525 (5.3 mb)
Телевизоры - WD-52525 (5.3 mb)
Телевизоры - WD-62725 (5.3 mb)
Телевизоры - WD-52525 (5.3 mb)