Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
S-VIDEO VIDEO Y–––––Pb–––––Pr R-A VIDEO 3 VIDEO 2 VIDEO 1 WOOFER AUDIO OUTPUT Y–––––Pb–––––Pr R-A R-A R-AUDIO-L(MONO) PTV BACK 1 STEREO AMPLIFIER 1 4 5 6 2 3 INPUT POWER REMOTE CONTROL 3 WOOFER AMPLIFIER 2 What you will need for connections: Audio Cable – 1 Audio Cable (RCA x 1) – 1 AUDIO CABLE AUDIO CABLE (RCA X 1) 18 PRECAUTIONS To ensure safe operation, please observe the following precautions: Use two (2) AAA alkaline batteries, see page 8. Replace both batteries at the same time. Do not use a new battery with a used battery. Risk of explosion, if battery is replaced by an incorrect type. If batteries have leaked in the remote control, carefully wipe the case clean and load new batteries. Do not expose the remote control to moisture or heat. REMOTE CONTROL KEYS q INPUT Key—Press to change the input signal source as follows: Analog RF . Digital RF . Video1 . Video2 . Video3 . HDMI . Analog RF. w NUMBER Keys—Two keys must be pressed to select a direct channel. Example: Press 0 then 6 to select channel 6. For Analog Cable channels above 100, press and hold the 1 key until C1- - appears, then press the other two numbers. e INFO Key—Press to display the Digital and Analog Full Banner information (press again to remove the display). Digital Full Banner display—Contains a two-part Channel Number (Major and Minor), and Tuner ID. If available, the following is also included: Station ID, VChip Program Rating, Program Title, Audio Info, and Signal Strength. Tuner ID Channel Major Minor Station ID Program Rating Program Title Audio Info Signal Strength Analog Full Banner display—Contains the Channel Number (analog antenna/cable), Tuner ID, Station ID (if available), Program Title (if available), V-Chip Program Rating, and Audio Info. Tuner ID Channel No. Station ID Program Rating Audio Info Program Title Point toward LCD Projection TV q w e r t u i o !1 !2 !3 !4 !8 !5 !6 !7 y !0 USING THE REMOTE CONTROL r RECALL Key—Select the first channel you want to !2 SLEEP Key—Press this key, then press the “0” key to watch; then select another channel using the NUMBER keys. Press RECALL to switch easily between the channels. Note: The RECALL key is inactive when an external input is selected (Video 1, Video 2, Video 3, or HDMI) and it cannot toggle between a Digital channel and an Analog channel. See TUNER key description. t MENU Key—Press this key to display the on-screen menu. y TUNER Key—Use this key to toggle from one tuning system to another, Digital channels and Analog channels. Note: The TUNER key is inactive when an external input is selected (Video 1, Video 2, Video 3, or HDMI). u CAPTION Key—Press to select analog or digital captioning. The Analog Caption modes are: CC1–CC4, Quikcap, and OFF. The Digital Caption modes are: Digital CC1–CC6, Quikcap, and OFF. i Channel Scanning (CH ed) Keys—Press e (up) d (down) keys to tune to the next higher or lower channel in the Channel Scan Memory list. The scanning loop includes analog channels, and digital channels. o PIX SHAPE Key—Use this key to change the video display format. Available options depend on signal received and the broadcast’s aspect ratio. They may include: PIX1, PIX2, PIX3, and PIX4. See simulated TV images below: PIX1 Gray colored borders appear at the sides, of the screen. Note: 4:3 image without distortion on a 16:9 screen. PIX3 Enlarges a PIX2 image vertically (some of the image may be cropped off). PIX2 A 16:9 image fills the screen normally. A 4:3 image is stretched horizontally and may appear distorted. PIX4 Stretches the PIX3 image horizontally (portions of the sides and/or top and bottom may be cropped off). !0 AUDIO Key—Press to select the desired audio mode (if available): DIGITAL: Main, Sub1, Sub2, Sub3, etc.; ANALOG: Stereo, Mono, SAP. !1 POWER Key—Press to turn the LCD Projection TV on or off. set the Sleep Timer. The desired time can be set from 30 minutes up to 3 hours in 30 minutes increments. To display the remaining time, press this key again. Sleep Timer will switch off the LCD Projection TV automatically. Note: The Sleep Timer cancels when the LCD Projection TV is turned off or if a power failure occurs. !3 MUTE Key—Press once to minimize the volume. Press again to restore. Note: This key will not mute the sound from the audio out jacks. !4 ENTER Key—Press this key to select an option from the menu system, when required. !5 Cursor e (up) d (down) Keys—Press these keys to move the cursor up and down within the menu. Cursor < (left) > (right) Keys—Press these keys to move the cursor left and right within the menu. !6 EXIT Key—Press this key to exit from the menu system. !7 Volume (VOL – +) Keys—Press the – + keys to adjust volume. The screen displays a left or right red arrow that blinks as many times as you press the VOL – + keys. !8 RESET Key—Press twice to restore factory settings. The LCD Projection TV will automatically start Channel Search and clear all customized settings (except for the lamp counter). Note: The Reset Function includ...
Эта инструкция также подходит к моделям:Телевизоры - PLV-55WHD1 (4.38 mb)