Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
4. Slide the tilt/swivel stand toward the front of the monitor until the latches click into the locked position. NOTE: For correct use of monitor, completely attach tilt/swivel base to the monitor. NOTE: To avoid self injury or damage to the monitor, attach and remove tilt/ swivel base with care. CAUTION: Make certain that the tilt/swivel base is locked firmly into place before turning the monitor upright. Removing the Tilt/Swivel stand 1. With the monitor unplugged from your system and the wall outlet, carefully turn the monitor upside down on a firm table. 2. Push down on the latch of the tilt/swivel base and slide the tilt/swivel base backward from the front of the monitor. 3. Pull out the tilt/swivel base from the slots on the bottom of the monitor. Slot Hook Latch Hook Firm Table AS500700700M900FINAL2.p65 3 11/11/03, 1:45 PM Quick Start –continued To attach the AccuSync™ monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. If necessary, install the display card into your system. For more information, refer to the display card manual. 3. For the PC: Plug the end of the video signal cable of the monitor in the video signal connector of the computer. (Figure A.1). Tighten all screws. For the Mac: Connect the Macintosh cable adapter (not included) to the monitor connector on the Macintosh (Figure B.1). Attach the 15-pin mini D-SUB end of the video signal cable to the Macintosh cable adapter on the computer (Figure B.1). Tighten all screws. NOTE: To obtain the AccuSync Macintosh cable adapter, call NEC-Mitsubishi Electronics Display of America, Inc. at (800) 632-4662. 4. Connect one end of the power cord to the AccuSync monitor and the other end to the power outlet (Figure C.1). NOTE: If you use this monitor at AC125-240V, please refer to Recommended Use section of this manual for proper selection of power cord. 5. Turn on the monitor and the computer. NOTE: If you have any problems, please refer to the Troubleshooting section of this User’s Manual. Figure A.1 15-pin mini D-SUB Captive Signal Cable 4 AS500700700M900FINAL2.p65 4 11/11/03, 1:45 PM Quick Start –continued 15-pin mini D-SUB Mac Adapter (Not Included) Figure B.1 Captive Signal Cable Figure C.1 Power Outlet Power Cord 5 AS500700700M900FINAL2.p65 5 11/11/03, 1:45 PM Controls (AccuSync 500) OSD (On Screen Display) control buttons on the front of the monitor function as follows: Control Direct Access Function The Contrast and Brightness functions are also available in the On Screen Display (OSD) menu. Button Bring up Contrast adjustment Bring up Brightness adjustment Buttons Use these buttons to choose or adjust items in the on screen display. MENU (or OSD) Button Use this button to enter or exit the on screen display. This Indicator lights up green when the monitor operates normally. If the monitor is in DPMS (Energy Saving) mode, this indicator color changes to amber. Power (DPMS) Indicator Use this button to turn the monitor on or off.Power Button Use this button to enter a selection in the on screen display. SELECT (or SET) Button Control Function Button 6 AS500700700M900FINAL2.p65 6 11/11/03, 1:45 PM Controls –continued (AccuSync 700/900) OSD (On Screen Display) control buttons on the front of the monitor function as follows: MENUSELECTControl Direct Access Function The Contrast and Brightness functions are also available in the On Screen Display (OSD) menu. Button Bring up Contrast adjustment Bring up Brightness adjustment Buttons Use these buttons to choose or adjust items in the on screen display. MENU (or OSD) Button Use this button to enter or exit the on screen display. This Indicator lights up green when the monitor operates normally. If the monitor is in DPMS (Energy Saving) mode, this indicator color changes to amber. Power (DPMS) Indicator Use this button to turn the monitor on or off.Power Button Use this button to enter a selection in the on screen display. SELECT (or SET) Button Control Function Button 7 AS500700700M900FINAL2.p65 7 11/11/03, 1:45 PM Controls –continued (AccuSync 700M) OSD (On-Screen Display) control buttons on the front of the monitor function as follows: 8 Control Direct Access Function The Contrast and Brightness functions are also available in the On Screen Display (OSD) menu. Bring up Contrast adjustment Bring up Brightness adjustment Buttons Buttons Control Function 1 3 2 7 6 5 4 Audio Mute Microphone MENU (or OSD) Button Buttons Buttons Power Button Power (DPMS) Indicator SELECT (or SET) Button Use this button to turn the monitor on or off. This Indicator lights up green when the monitor operates normally. If the monitor is in DPMS (Energy Saving) mode, this indicator color changes to amber. Use this button to enter a selection in the on screen display. Use to mute audio source. Built-in microphone. Brings up to the audio menu. Use these buttons to choose or adjust items in the on screen display. Use this button to enter or exit the on screen display. 31 2 7654 AS500700...