Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
No heating will occur in this mode. 3. Oscillating feature (BDHF501 model): To activate this feature, press OSCILLATION button on unit. Press a second time to turn it off. 4. Comfort control (Thermostat): For heat, press ON/FAN/HEAT button twice. Heater has 5 preset temperature regulating settings: Frost Watch 4,4 °C (40 °F), 18,3 °C (65 °F), 21,1 °C (70 °F), 24 °C (75 °F) and 27 °C (80 °F). You can set the temperature of your choice by pressing the COMFORT button to your desired temperature level. Heater will deactivate when room reaches the set temperature. It will restart once room temperature has fallen 5 °F below set temperature. Press ON/FAN/HEAT button a third time to turn off unit (B). 5. Timer Auto Off: The timer can be programmed in one-hour increments up to a maximum of 10 hours. a) Press the TIMER ON button on heater control pad or remote control (BDCH551 model only) once for each hour increment you want. b) A light or lights will illuminate on control panel to indicate how many hours you have selected. For example, if all four lights are lit, the total programmed time is 10 hours, if the 3-hour and 4-hour lights are lit, total programmed time is 7 hours. The lights will turn off as time elapses. c) Unit will shut off automatically once the selected time runs out. d) When timer and frost watch are activated at same time, unit will turn off according to your timer setting (C). 6. Frost Watch: You can adjust your thermostat to its lowest setting or Frost Watch. Your heater will remain off unless the temperature drops below 4 °C (40 °F). If this happens, FROST WATCH will automatically cycle the heater on. 7. Remote control (D) (BDHF551 model) Requires 2 LR44 batteries (included). To insert batteries: Turn remote control to its back side. Slide cover at bottom until it comes off. Insert two LR44 batteries Close cover by sliding it onto remote control. Remote can be stored in unit handle space when not in use. To use remote, point it at the heater with no objects between the remote and heater. Follow same instructions as control panel. Note: Remote control unit contains buttons with symbols only. Special features and the Advanced Safety Technology™ (AST) system 1. This unit is equipped with a safety auto off and thermal cut off. If the unit experiences excessive heat, the safety auto off will shut off unit. If this happens, press ON/FAN/HEAT button a third time to turn off unit. Be sure front and back grilles are not blocked and nothing is restricting airflow. If unit fails to operate after 10 minutes, it may mean heater has internal damage and thermal cut off has been tripped so heater can no longer operate. 2. Motion-off detection feature: Cuts the power if unit falls over in any direction or is lifted (such as if you move it to another part of the room). 3. Tip-over switch: Cuts the power if unit is knocked over forward or backward. Both are controlled by the tipover switch on bottom of unit. Do not attempt to defeat this safety feature. 4. The POWER indicator light shows the heater is switched on and operating. It continues to glow even if the thermostat has cycled and heating elements are off. Even though this unit has a cool-touch housing, both front and back grilles will get hot. Be careful not to touch them. 5. Manual resettable limiting thermostat: Provides backup overheating protection by cutting power in case of overheating. In the event the thermal cut-off is activated, the power to the unit will stop but the power light will remain illuminated. To reset the unit: a) Unplug the unit from wall. b) Wait 10 minutes. c) Plug unit back in and push the RESET button on the ALCI plug. d) Turn unit power on. Care and Cleaning This heater is permanently lubricated and will not require additional lubrication for the life of unit. It contains no user serviceable parts. Refer service to qualified service personnel. 1. Always turn unit off, unplug, disconnect the cord from outlet, and allow heater to cool completely before cleaning. 2. To clean exterior, use a soft dry cloth or one moistened with a mild detergent to wipe outside surfaces. Do not use abrasives or harsh cleansers. Dry surfaces thoroughly before using heater. Or, you can use a vacuum with a dusting brush attachment to clean away dust. Caution: Do n...
Эта инструкция также подходит к моделям:Вентиляторы - BDHF501 (2.06 mb)