Оценок - 5, средний балл: 4 ( )

Производитель: GE Размер: 595.3 kb Название файла: 981340EN.pdf Язык инструкции:

There may be dust inside a brand new tumble dryer. Sort out the laundry • To prevent bundling of laundry: close zips, button up pillow cases and duvet covers; tie any strings, such as apron strings. • Empty pockets. • Remove any metal parts (paper clips, safety pins, etc. ....). • Turn garments made of double layer fabrics inside out (e. g. turn anoraks with cotton lining inside out), so that they will dry better. • Shake out the laundry. Open the door • Open the door by presing on the left side as per picture Load the laundry Warning! When closing the door, do not trap any garments! The fabrics could get damaged. Please check the laundry does not get caught between the door and filter. • Put the prepared and shaken out laundry into the dryer. Drying Switch the machine on - select the drying programme/time • Select the drying programme or time. The lights “DROGEN/SECHAGE”, “AFKOELEN/REFROID.” and “EINDE/FIN” come on. The light of the “START/PAUSE-MARCHE/PAUSE” button flashes and the display shows the duration of the programme. If required, press the “LAGE TEMP/DELICAT” button and/or the “ZOEMER/ ALARME” button or the “KORT/COURT” button. Select the “STARTUITSTEL/D.DIFF.” if required. The selected delay appears on the display for 2 seconds, then the duration of the selected programme is displayed. Start the machine Press the “START/PAUSE-MARCHE/PAUSE” button: the corresponding light stops flashing and drying starts. Only the “DROGEN/SECHAGE” light stays lit. If you have selected the “STARTUITSTEL/D.DIFF.”, the machine begins its countdown. The drum turns alternately in both directions during drying. All drying programmes end with a 10 minute cooling phase (light “AFKOELEN/REFROID.” is on). The “EINDE/FIN”and “FILTER/FILTRE” lights illuminate. The display shows a static zero and the buzzer sounds to indicate the end of the cycle. You may remove the laundry after this phase. Remove or add laundry It is possible to interrupt the drying cycle at any time in order to remove or add laundry. Open the door. Caution! Laundry and drum can be hot. Remove or add laundry. Close the door and press “START/PAUSE-MARCHE/PAUSE” button to continue the drying cycle. Drying End of drying cycle If the laundry is not removed at the end of the cycle, the dryer performs an anti-creasing phase (duration: 30 minutes maximum). If you do not remove the laundry, the dryer will stop automatically at the end of the anti-creasing phase. The “EINDE/FIN” and “FILTER/FILTRE” lights remain lit and the buzzer sounds for 2 minutes. The light of the “START/PAUSE-MARCHE/PAUSE” button goes off and a flashing zero appears on the display. Switch the tumble dryer off Turn the programme selector dial to “UIT/ARRET”; all the lights go out. The appliance is switched off. Remove the laundry. If you open and then close the door before turning the programme selector dial to “UIT/ARRET”, all the lights corresponding to the phases making up the performed programme come on and the display shows the duration of the programme. Important! If the drying programme has to be stopped before it reaches the end, we recommend that you turn the programme selector dial to position “AFKOELEN/REFROID.” and wait until the end of this phase before removing the laundry. This will avoid a build-up of heat inside the appliance. To do this first turn the dial to “UIT/ARRET” and then to “AFKOELEN/REFROID.” and depress “START/PAUSEMARCHE/ PAUSE” button. Clean the filters To ensure free circulation of air during the drying cycle, the fluff filters must be cleaned after each drying cycle, before removing the laundry. Adjusting the level of conductivity Adjusting the level of conductivity Water contains, a variable quantity of limestone and mineral salts of which quantities vary according to geographical locations thus varying its conductivity values. Relevant variations of the conductivity of the water compared to those prefixed by the factory could slightly influence the residual humidity of the laundry at the end of the cycle. Your dryer allows you to regulate the sensitivity of the drying sensor based on conductivity values of the water by using the following procedure. Procedure: Turn the programme selector dial to switch on the appliance In selection mode press simultaneously the buttons 3 and 6 until «C CC0 00» appears on the digits. Adjusting the level of conductivity: Press the button 5 sequentially: the level of conductivity is indicated by the lighting of the horizontal hyphens. DISPLAY Conductivity degree Approximative value .S/cm (25°C) C CC 0 00 - -- Low < 300 C CC 0 00 - -- - -- Medium 300 - 600 C CC 0 00 - -- - -- - -- High > 600 Normally, the appliance is factory-set to the highest level; however, certain models may be configured differently. Memorizing the new setting: Simultaneously press down the buttons 3 and 6 until the previous drying cycle time appears again on the display and the buzzer sounds. Programme Chart Programme Chart Automatic drying (electronic pro...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: