Оценок - 3, средний балл: 5 ( )

Производитель: GE Размер: 558.41 kb Название файла: b03a7bc2-63c9-4b26-98f9-acbd64a38a70.pdf Язык инструкции:

The Lint Filter: Clean the lint filter before each use. Moisten your fingers and reach into the filter opening. Run your fingers across the filter. Have a qualified technician vacuum the lint from the dryer once a year. The Exhaust Duct: Inspect and clean the exhaust ducting at least once a year to prevent clogging. A partially clogged exhaust can lengthen the drying time. Follow these steps: 1 Turn off electrical supply by disconnecting the plug from the wall socket. 2 Disconnect the duct from the dryer. 3 Vacuum the duct with the hose attachment and reconnect the duct. The Exhaust Hood: Check with a mirror that the inside flaps of the hood move freely when operating. Make sure that there is not wildlife (birds, insects, etc.) nesting inside the duct or hood. Fabric Care Labels Below are fabric care label “symbols” that affect the clothing you will be laundering. WASH LABELS DRYLABELS Machine wash cycle cycle Normal Permanent Press/ Gentle/Do not wash Do not wringwrinkle resistant delicate Hand wash Water temperature Hot Warm Cold/cool (50°C/120°F) (40°C/105°F) (30°C/85°F) Tumble dry Dry Normal Permanent Press/ wrinkle resistant Gentle/ delicate Do not tumble dry Do not dry (used withdo not wash) Heat setting High Medium Low No heat/air Specialinstructions Line dry/ hang to dry Drip dry Dry flat In the shade BLEACH LABELS Bleach symbols Any bleach Only non-chlorine bleach Do not bleach (when needed) (when needed) 10 Venting the Dryer For the best drying performance the dryer needs to be properly vented. The dryer will use more energy and run longer if it is not vented to the below specifications. Carefully follow the details on Exhausting in the Installation Instructions. ¦ Use only rigid metal or flexible metal 4. diameter ductwork inside the dryer cabinet or for exhausting to the outside. n Do not use plastic or other combustible ductwork. n Use the shortest length possible. n Do not crush or collapse. n Avoid resting the duct on sharp objects. n Venting must conform to local building codes. Correct Venting Incorrect Venting 11 Customer ServiceTroubleshooting TipsOperating InstructionsSafety Instructions Operating Instructions Safety InstructionsCustomer Service Troubleshooting Tips Before you call for service… Troubleshooting Tips Save time and money! Review the charts on the following pages first and you may not need to call for service. Problem Possible Causes What To Do Dryer doesn’t start Dryer is unplugged • Make sure the dryer plug is pushed completely into the outlet. Fuse is blown/circuit breaker is tripped • Check the house fuse/circuit breaker box and replace fuse or reset breaker. NOTE: Most electric dryers use two fuses/breakers. Dryer doesn’t heat Fuse is blown/circuit breaker is tripped, the dryer may tumble but not heat • Check the house fuse/circuit breaker box and replace fuse or reset breaker. Gas service is off • Make sure gas shutoff at dryer and main shutoff are fully open. Dryer shakes or makes noise Some shaking/noise is normal. Dryer may be sitting unevenly • Move dryer to an even floor space, or adjust leveling legs as necessary until even. Greasy spots on clothes Improper use of fabric softener • Follow directions on fabric softener package. Drying dirty items with clean ones • Use your dryer to dry only clean items. Dirty items can stain clean items and the dryer. Clothes were not completely clean • Sometimes stains which cannot be seen when the clothes are wet appear after drying. Use proper washing procedures before drying. Lint on clothes Lint filter is full • Clean lint screen before each load. Improper sorting • Sort lint producers (like chenille) from lint collectors (like corduroy). Static electricity can attract lint • See suggestions in this section under STATIC. Overloading • Separate large loads into smaller ones. Paper, tissue, etc. left in pockets • Empty all pockets before laundering clothes. Static occurs No fabric softener was used • Try a fabric softener. • Bounce® Fabric Conditioner Dryer Sheets have been approved for use in all GE Dryers when used in accordance with the manufacturer’s instructions. Overdrying • Try a fabric softener. • Adjust controls for less drying. Synthetics, permanent press and • Try a fabric softener. blends can cause static Inconsistent drying times Type of heat • Automatic drying times will vary according to the type of heat used (electric, natural or LP gas), size of load, types of fabrics, wetness of clothes and condition of exhaust ducts. 12 Problem Possible Causes What To Do Clothes take too long to dry Improper sorting • Separate heavy items from lightweight items (generally, a well-sorted washer load is a well-sorted dryer load). Large loads of heavy fabrics (like beach towels) • Large, heavy fabrics contain more moisture and take longer to dry. Separate large, heavy fabrics into smaller loads to speed drying time. Controls improperly set • Match control settings to the load you are drying. Lint filter is full • Clean lint filt...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: