Оценок - 5, средний балл: 3.8 ( )

Производитель: Alliance Laundry Systems Размер: 2.02 mb Название файла: Язык инструкции:

Then set the reverse control switch to “nonreversing” and note that the cylinder turns constantly clockwise as viewed from the front of the tumbler. If not, interchange L1 and L2 power leads to the reverse drive motor. M414545 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 53 ELECTRONICALLY CONTROLLED OPL TUMBLER INTRODUCTION Drying can be done automatically or by time dry. When drying automatically, the tumbler stops drying when laundry reaches the factory set or programmed dryness level and starts cool down. When time drying, the tumbler stops drying when programmed time ends and starts cool-down. Special Cycle allows user to specify the number of heating cycles and specify temperature from 80°F (27°C) to 180°F (82°C) for all heat cycles. Special Time allows user to specify temperature from 80°F (27°C) to 180°F (82°C) for all heat cycles. Both automatic and time dry have factory-set cycles, but other cycles can also be created. Frequently used cycles can be saved in the control's memory as Custom cycles. Refer to Figure 25. A drying instructions chart is included for recording selections and settings for various load types. Refer to Figure 31. In all cycles, except No Heat, Wrinkle-Free begins when Cool Down ends. During Wrinkle-Free, the tumbler alternately stops for 2-1/2 minutes and then runs without heat for 2-1/2 minutes until door is opened or 60 minutes has elapsed. All pads can be pressed in any sequence without damaging control or tumbler. To stop the tumbler at any time, open the door or press STOP/RESET. The window display will flash. Press STOP/RESET twice (within 3 seconds) to end the cycle and reset the control to idle status. Refer to Figure 24. NOTE: Not all tumblers will have reversing option. OPL Micro Control Panel Figure 24 54 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M414545 © Copyright, Alliance Laundry Sys M414545 tems LLC – DO NOT COPY or TRANSMIT 55 Figure 25 STATUS LIGHTS, SIGNAL AND REVERSING DOOR OPEN Lights when door is open. Note: Display window also flashes. DRYING Lights when laundry is drying. COOL DOWN Lights when laundry is cooling. CUSTOM Lights when a Custom cycle is programmed, recalled or running. SIGNAL When lit, the signal will sound when the laundry is ready for removal. The signal has three loudness levels. These can be set anytime the control is activated. Pressing the SIGNAL pad once produces the softest tone. Additional presses produce louder tones. The fourth press turns tone and light off. The loudness level selected is for all cycles until changed. When the signal is on and any key pad is pressed, it sounds at the selected level to confirm the pad was properly pressed. REVERSING When lit, the cylinder will rotate (For Reversing in one direction for 25 seconds, Models only) pause for 6 seconds, then rotate in opposite direction for 25 seconds. This sequence will repeat until the selected cycle ends. To turn Reversing option off, press the REVERSING pad. (Any time reversing pad is pressed, the cylinder will pause for 6 seconds.) DRYING LAUNDRY 1. LOAD TUMBLER – Open loading door. Shake out laundry and place in tumbler. 2. CLOSE DOOR – Tumbler will not operate with open door. WARNING To reduce the risk of bodily injury, the tumbler stops tumbling when the door is opened. Do not use the tumbler if it does not stop tumbling when the door is opened or starts tumbling without pressing the START pad. Remove the tumbler from use and call for service. W078 NOTE: Do not press directly on lights or the center of pad. For proper selection, press on pad slightly to the right of center. STATUS Lights Figure 26 56 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M414545 3. SELECT FABRIC TYPE – Press an ON/SELECT pad to select a temperature. HIGH, MEDIUM, MEDIUM LOW, LOW or NO HEAT for items that should not be dried with heat. A light to the left of the selected pad lights up. AC:** will be displayed when tumbler is in Auto Cool Down. Typical cool down times for fabric selections are preset. Refer to Table 9. The cool down time can only be altered before cycle is started. To alter cool down time press the COOL DOWN pad and then press the MORE or LESS pad (when cool down time is altered, TC:** will be displayed). For 1 minute changes, press pad and release. For 5 minute changes, press pad and hold. Cooling time can be from 1 to 39 minutes. To return to the Auto Cool Down, press MORE or LESS pad until AC:** is displayed. ON/SELECT Pads Figure 27 4. SELECT CYCLE (AUTOMATIC, TIME DRY OR CUSTOM) A. Automatic Dry and Condition When a temperature is selected, “A0:00” will appear in the display window. Press START to start the tumbler. “A*:**” will appear in the display window. The first “*” is the selected dryness level (dryness levels less than zero will appear as “-*”), and the “:**” is the elapsed time. The degree of dryness can be altered. Use the MORE pad, or the LESS pad, to increase or decrease dryness level....

Скачать инструкцию

Чтобы скачать, введите 2 цифры: