Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
5.Close loading door. 16 Cleaning and maintenance Cleaning lint filter To ensure that the dryer works efficiently, the lint filters (micro-fine filter and fine strainer) must be cleaned after every drying cycle. 1 Caution! Never operate the dryer without fluff filters or with damaged or blocked fluff filters. 1. Open door 2. Use a damp hand to clean the micro- fine filter, which is built into the lower part of the loading aperture. 3. Push down unlock button on large mesh filter. Large mesh filter elevates. 4. Take out fine strainer. 5. Remove fluff from fine strainer. It is best to use a damp hand for this purpose. Clean the entire filter area 3 The strainer area does not have to be cleaned after every drying cycle, but should be checked regularly and cleaned of fluff if necessary. 6.To do this, grip the top of the large mesh filter and pull it forwards until it comes loose from the two brackets. 7.Remove fluff from the entire filter area. It is best to use a vacuum cleaner for this purpose. 8.Press both lugs of the large mesh filter into the brackets on the loading door until they snap into place. 9.Re-insert fine strainer. 10. Press against the large mesh filter until it locks into the interlock. 3 If the fine strainer is not fitted, the large mesh filter will not snap into place and the door cannot be closed. Cleaning the door seal Wipe the door seal with a damp cloth immediately after the drying cycle has finished. Emptying the water reservoir Empty water reservoir after every drying cycle. If the water reservoir is full, an active programme will be interrupted automatically and the EMPTY WATER display will light up. In order to continue the programme, the water reservoir must be emptied. 1 Warning! The condensed water is not suitable for drinking or for preparing foodstuffs. 1.Take out drawer containing water reservoir completely (1) and pull up the water reservoir’s drainage pipe as far as it will go (2). 2.Pour condensed water out into a sink or other suitable container. 3.Slide outlet connections in and re fit water reservoir. If the programme has been interrupted as a result of the water reservoir being full: Press the START/PAUSE button to continue the drying cycle. 3 The water reservoir has a volume of approx. 4 litres. This is sufficient for around 6kg of laundry which has previously been spun at 800 revolutions/ minute. 3 The condensed water can be used as distilled water, e.g. for steam ironing. However first filter it (e.g. with a coffee filter) to remove any residue and small pieces of fluff. Cleaning heat exchanger If the HEAT EXCHANGER display is illuminated, the heat exchanger needs to be cleaned. 1 Caution! Operating when the heat exchanger is clogged with lint can damage the dryer. This also increases energy consumption. 1.Open loading door 2.Open base door. To do this, press the release button located beneath the loading aperture and open the base door to the left. 3.Remove lint from the inside of the door and the heat exchange chamber. Wipe the door seal with a damp cloth. 4.Turn both lock washers inwards. 5.Use the handle to pull the heat exchanger out of the base and carry it horizontally to prevent any remaining water from spilling. 6.To empty the heat exchanger, hold vertically over a washing-up bowl. 1 Caution! Do not use sharp objects to clean the heat exchanger. You could damage it an cause leaks. 7.Clean heat exchanger. It is best to use a brush or to rinse thoroughly with a shower head. 8.Replace heat exchanger and lock into place (turn both lock washers outwards until they snap into place). 9.Close base door. 3 The dryer will not operate if the HEAT EXCHANGER indicator is still lit. 1 Caution! Never operate the dryer without the heat exchanger. Cleaning the drum 1 Caution! Do not use abrasives or steel wool to clean the drum. 3 Lime in the water or cleaning agents may form a barely visible lining on the inside of the drum. The degree to which the laundry has been dried is then no longer detected reliably. The laundry is damper than expected when removed from the dryer. Use a damp cloth, which has been soaked in water and a little vinegar, to wipe the inside of the drum and drum ribs. Clean operating screen and housing 1 Caution! Do not use furniture cleaners or aggressive cleaning agents to clean the machine. Use a damp cloth to wipe down the operating screen and housing. What to do if … Troubleshooting by yourself If, during operation, the error code (E plus number or letter) appears on the multi-display: Switch the machine off and on again. Reset programme. Press the START/PAUSE button If the error is still displayed, please inform your local Service Force Centre and quote the error code. Problem Possible cause Remedy Mains plug is not plugged in Plug in at mains socket. Check or fuse is not working corfuse in fuse box (domestic inrectly. stallation). Dryer does not work. Loading door is open. Close loading door. Have you pressed the START/ Press the START/PAUSE button PA...