Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Questions? You'll Need a Few Things Before You Begin See Owner's Manual or call Duct Tape _" Power Cord (3-wire or 4-wire) Amana and Strata Relief Wrench Consumer Screw Drivers Affairs Scrows ggg (supplied) Level Department i .Z <<_ ::_1 i<. _ 1-800-843-0304 Optional Kits REMOVE PARTS Kits are available at extra cost through AND CLEAN your Amana dealer or DRYER DRUM Amana factory 1-800-843-0304. Wipe drum with clean rag and soap Directional Exhaust Kit diluted in warm water to remove any DK1 Sales Accessory (Directional oil used in manufacturing. Make a Exhaust Kit #528P3). paste of laundry detergent and clean drum if necessary. Flexible Metal Vent Kit Exhausting the dryer in hard-to-reach To reverse the direction that door locations can be accomplished by opens, see the Owner's Manual. installing Kit # 521P3. CONNECT DRYER TO EXHAUST SYSTEM Secure all joints with clamps or duct tape. DO NOT use sheet metal screws or other fastening means which extend into the duct to attach exhaust pipe joints. They could catch lint and reduce the efficiency of the exhaust system. IMPORTANT: Keep exhaust duct as short as possible. Be sure old ducts are clean before installing your new dryer. To prevent backdraft when dryer is not in operation, outer end of exhaust pipe must have a weather hood with hinged dampers (obtain locally). Weather hood should be installed at least 12" (30.5 cm) above the ground. Higher clearances may be necessary in areas where heavy snowfall can occur. No extra system length consideration is necessary when exhausting through the roof. Use MAXIMUM EXHAUST LENGTH table to calculate system length. Use a roof cap that provides air flow equal to weather hood. Exhaust Directions Dryer can be exhausted to the outdoors through the back, left, right or bottom of the dryer. Dryer is shipped from factory ready for rear exhaust, No kits required. To exhaust dryer through sides or bottom, install a DK1 Sales Accessory (Directional Exhaust Kit 528P3). Available as optional equipment at extra cost. ( Exhaust System Materials Use Exhaust duct must be tour inches (10.2 cm) in diameter without obstructions. Rigid metal duct is recommended. Non-combustible semi-rigid flexible metal duct is acceptable. _ Rigid Metal Semirigid Metal DO NOT use plastic pipe, foil pipe, or flexible plastic pipe, because it tt-Do Not Use contributes to poor drying performance and collects lint, which can lead to a fire hazard. To identify flexible foil or plastic duct, pinch the coils of the duct between your fingers. If the coils can be brought together, do not use the duct. k. Flexible Foil Plastic ._ Maximum Exhaust Length Rigid Metal Duct Number of Weather Hood Weather Hood 90QElbows 4-inch Opening 2Y2-inch Opening 0 44 feet (13.4 m) 34 feet (10.4 m) 1 34 feet (10.4 m) 26 feet (7.9 m) 2 26 feet (7.9 m) 20 feet (6.1 m) 3 20 feet (6.1 m) 14 feet (4.3 m) Flexible Metal Duct Number of Weather Hood Weather Hood 90g Elbows 4-inch Opening 21/2-inchOpening 0 24 feet (7.3 m) 20 feet (6.1 m) 1 20 feet (6.1 m) 16 feet (4.9 m) 2 16 feet (4.9 m) 12 feet (3.7 m) 3 12 feet (3.7 m) 8 feet (2.4 m) NOTE: Deduct 6 feet (1.8 m) for each additional elbow. Recommended Weather Hood Recommended for Short Runs Only 4" (10.16 cm) 2-1/2" (6.35 cm) 4" (10.16 cm) 3-wire or 4-wire Plug Connection Four-wire cord is required for mobile homes or where codes do not permit CONNECT ELECTRICAL grounding through neutral. CORD 1. Remove access cover from rear of dryer. 2. Use a strain relief and insert end of power cord through power supply Access hole. covet" 3. Use the three screws from envelope located in the drum to attach the remaining power cord wires to the terminal block as follows: • Red wire to "LI" terminal. • Black wire to "L2" terminal. • White wire to Neutral terminal. • 4-wire Plug Only--Remove ground screw and detach ground wire from bulkhead. Attach power cord ground (green) wire to rear bulkhead using ground screw. Attach free ground wire, previously Strain relief attached with ground screw, with white wire to the neutral (center) (not supplied with dryer) terminal on the terminal block. 4. Tighten all screws and reinstall access cover removed in step 1. 3-wire Cord Installed 4-wire Cord Installed Ground ;_ wire '%1" "L2" "LI" "L2" Neutral _r_ II Neutral Orou dJ 76 White Red White Black Green Black POSITION AND LEVEL DRYER Place dryer in position, adjust all legs (4) until dryer is level side to side and front to back. Important Safety Information About Ground Wires In the event of an electrical short circuit, a ground wire reduces the risk of electric shock by providing an escape wire for the electric current. Standard accepted color coding for ground wires is green or green with a yellow stripe. Grounding wires and wires colored like grounding wires are NOT to be used as current carrying conductors. WARNING ] To reduce the risk of fire, the dryer MUST be exhausted to the outdoors. DO NOT exhaust dryer air into a window well, gas vent, chimney or enclos...