Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
• NEVER leave child unattended. High Chair Use: • ALWAYS secure child with restraint belts adjusted to fit your child snugly. The tray is not designed to hold child in the product. When attached to adult chair: • Use restraint belts until child is able to get in and out of the product without help (about 21/2 years old). • NEVER use in motor vehicles. • ALWAYS secure the product on a chair using bottom and back attachment straps. NEVER use on a stool or bench that does not have a seat back. To prevent falls: • NEVER release the seat with child in product. • NEVER carry child in the seat. IMPORTANT! PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE. • Please read these instructions before assembly and use of this product. • Adult assembly is required. • Tool needed for assembly: Phillips screwdriver (not included). • When using this product on an adult chair: -Make sure the chair seat is level and larger than the seat base. -DO NOT use on a folding chair. -Check to be sure the floor surface beneath the chair is level. • Product features and decorations may vary from photographs. 2 3 Note: Tighten and loosen all screws with a Phillips screwdriver. Do not over-tighten the screws. FASTENERS SHOWN ACTUAL SIZE #8 x ." Screw with Plastic Retainer – 4 #8 x ." Blunt Screw – 4 #8 x ." Pointed Screw – 2 Seat Support Parts Front Base Rear Base Footrest 2 Frames IMPORTANT! Please remove all parts from the package and identify them before assembly. Seat Back Pad Seat with Restraint Seat Pad Seat Back with Restraint Tray Hint: Do not remove the plastic inserts inside the tubes of the front base. Hint: Do not remove the plastic insert inside the tube in each frame. 2 Brackets (Left and Right) Assembly CAUTION This package contains small parts in its unassembled state. Adult assembly is required. IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts. Rear Base1 Tapered Frame Tube With the Fisher-Price® logo facing out, fit the tapered frame tube into the rear base. 2 • Fit a #8 x ." screw with retainer into the rear base and tighten. • Repeat steps 1 and 2 to assemble the other frame to the rear base. 3 Frame Latches Frame Assembly Frame Tubes Seat Support • Lay the frame assembly down with long frame tubes up. • Position the seat support with the frame latches down. • Slide the seat support onto the frame tubes. Hint: Push the seat support all the way to the top of the assembly. You will hear several "clicks". 4 5 • Lift the frame assembly upright. • Fit the footrest onto the seat support, as shown. 6 Assembly • Fit the front base into the frame tubes. 4 • Insert two #8 x ." screws with retainers into the holes in each frame tube and tighten. Hint: If you cannot insert the screws into the frame tubes, you have assembled the front base backwards. Remove it, turn it around and re-assemble it to the frame tubes. 5 Front Base Footrest Seat Support • Insert two #8 x ." blunt end screws into the holes on each side of the footrest and tighten. 7 Footrest 6 • Turn the frame over with the footrest facing away from you. • First fit the left bracket (labeled 1) onto the seat support tube closest to you A . • Then, slide the left bracket completely onto the seat support B . Hint: The brackets are designed to fit each side of the seat support one way. If the bracket does not seem to fit, try the other one. 8 • Push to align the slot in the left bracket with the hole in the seat support. • Insert a #8 x 3/4" pointed end screw through the left bracket and into the seat support and tighten. 9 Assembly • First fit the right bracket (labeled 2) onto the seat support tube closest to you A . • Then, slide the right bracket completely onto the seat support B . 10 • Push to align the slot in the right bracket with the hole in the seat support. • Insert a #8 x 3/4" pointed end screw through the right bracket and into the seat support and tighten. • Turn the frame upright. 11 Seat Support Seat Support Right Bracket Left Bracket Seat Support Tube Seat Support Tube A B A B 7 • Unbuckle the lower restraint. 13 Tab Tab Slot Slot Assembly • At an angle, fit the tabs on the seat back into the slots in the seat. • Push the seat back to “snap” in place. • Pull on the seat back to be sure it is secure to the seat bottom. 12 • Pull the ends of the waist belts and crotch belt through the slots in the seat pad. • Fit the elastic loops on the seat pad down through the slots in the seat. • Turn the seat upside down. • Pull the elastic loops through the slots in the seat and fit the elastic loops to the pegs. 14 Seat Pad Elastic Loops Pegs 8 Assembly • Pull the ends of the shoulder belts through the slots in the seat pad. • Fit the straps on the back of the seat back pad into the slots in the seat back pad. • Press to fasten the straps to secure t...