Оценок - 3, средний балл: 3
(
)
)
|
Фрагмент инструкции
For a replacement trigger or to order a bump action trigger contact your authorized service center or call 1-888-848-5175. tO ReplACe seqUentiAl tRiGGeR (ns100B only) Trigger Removal (Fig. 2) 1. Lock off trigger. 2. Remove air from the tool. 3. Remove rubber grommet (N) from end of dowel pin (M). 4. Remove dowel pin. 5. Remove trigger assembly from trigger cavity under the handle of the tool housing. Trigger Installation 1. Insert the trigger kit into trigger cavity. 2. Ensure that trigger spring (O) is placed around the trigger valve stem. 3. Align the holes of the trigger with the housing holes, then insert the dowel pin (M) through the entire assembly. 4. Push the rubber grommet (N) onto the end of the dowel rod. opERATIoN pREpARING THE TooL Read the section titled important safety instructions for Pneumatic Tools at the beginning of this manual. Always wear proper eye [ANSI Z87.1 (CAN/CSA Z94.3)] and hearing protection [ANSI S12.6 (S3.19)] when operating this tool. Keep the stapler pointed away from yourself and others. For safe operation, complete the following procedures and checks before each use of the stapler. nOte: These nailers are designed to be used without oil. 1. Before you use the nailer, be sure that the compressor tanks have been properly drained. 2. Wear proper eye, hearing and respiratory protection. 3. Lock the magazine release in the back position and remove all fasteners from the magazine. 4. Check for smooth and proper operation of contact trip and pusher assemblies. Do not use tool if either assembly is not functioning properly. NEVER use a tool that has the contact trip restrained in the up position. 5. Check air supply. Ensure that air pressure does not exceed recommended operating limits; 70 to 120 psi, (4.9 to 8.3 bar, 5 to 8.5 kg/cm2). 6. Connect air hose. 7. Check for audible leaks around valves and gaskets. Never use a tool that leaks or has damaged parts. UsinG the lOCK-Off (ns100B, fiG. 1, 2) To reduce the risk of injury. AlWAYs wear proper eye [ANSI Z87.1 (CAN/CSA Z94.3)] and hearing protection [ANSI S12.6 (S3.19)] when operating this tool. Do not keep trigger depressed when tool is not in use. Keep the lock-off switch rotated to the right (OFF) when the tool is not in use. Serious personal injury may result. Lock off trigger, disconnect air line from tool and remove fasteners from magazine before making adjustments or personal injury may result. The NS100B stapler is equipped with a trigger lock-off switch (J) which when rotated to the right, prevents the tool from actuating. When the switch is in the unlocked position, the tool will be fully operational. The trigger should always be locked off whenever any adjustments are made or when tool is not in use. LoADING THE TooL (FIG. 3) Keep the tool pointed away from yourself and others. Serious personal injury may result. Never load fasteners with the contact trip or trigger activated. Personal injury may result. Disconnect tool from air supply before removing or re-installing no-mar pad. 1. Read all safety Warnings before using tool. 2. Connect to air supply. 3. Lock off trigger. (NS100B only) 4. Push the magazine release (F) then slide magazine (E) to open chamber. 5. Position stapler on a stable surface so contact trip is pointing upward and away from you. 6. Insert fasteners into the top chamber of the magazine. 7. Slide magazine until it clicks, securing the magazine. ACtUAtinG tOOl To reduce the risk of injury, AlWAYs wear proper eye [ANSI Z87.1 (CAN/CSA Z94.3)] and hearing protection [ANSI S12.6 (S3.19)] when operating this tool. The NS150B can be actuated using one of two modes: single sequential action trigger mode and bump action trigger mode. The NS100B can be actuated using the single sequential action trigger mode. Sequential action trigger - (Fig. 1, 5) A fastener will fire each time the trigger is depressed as long as the contact trip remains depressed which could result in inadvertant actuation. The sequential action trigger’s intended use is for intermittent fastening where very careful and accurate placement is desired. The NS100B is ready to use in the sequential action trigger mode. On the NS150B, push selectable trigger button (A) from back of trigger and turn indicator to the position. The tool is now ready to operate in the single sequential action trigger mode to operate the stapler in sequential action mode: 1. Depress the contact trip firmly against the work surface. 2. Depress the trigger. Bump action trigger - (Fig. 1, 5) The bump action trigger’s intended use is for rapid fastening on flat, stationary surfaces. Using the bump action trigger, two methods are available: place actuation and bump actuation. On the NS150B, push selectable trigger button (A) from back of trigger and turn indicator to the position. The tool is now ready to operate in the single sequential action trigger mode To operate the tool using the plACe ACtUAtiOn method: 1. Depress the contact trip against the work surface. 2. Dep...
Эта инструкция также подходит к моделям:Строительные пистолеты - NS150B (3.82 mb)