Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Do not use the tool if the contact trip safety mechanism is not working correctly. 1. Disconnect the air supply from the tool. 2. Remove all fasteners from the magazine. Make sure not to pull the trigger or depress the contact trip safety mechanism when connecting the tool to an air compressor. Serious personal injury or property damage can occur if the tool cycles. 3. Make sure the trigger and contact trip safety mechanism move up and down without any sticking or binding. 4. Reconnect air supply to the tool. 5. Depress the contact trip safety mechanism against the work surface without pulling the trigger. The tool must not cycle. Do not use the tool if a cycle occurs. 6. Hold the tool clear of the work surface. The contact trip safety mechanism should return to its original down position. Pull the trigger. The tool must not cycle. Do not use the tool if a cycle occurs. 7. Depress the contact trip safety mechanism against the work surface. Pull the trigger. The tool must cycle. LOADING THE TOOL Disconnect tool from air supply before adjusting, clearing jams, servicing, relocating or during non-operation. Failure to do so could result in serious injury or property damage. Never place your hand or any part of your body in the fastener discharge area of the tool when air supply is connected to the tool. Serious personal injury may occur. PAGE 10 NOTE Use DeVilbiss Air Power fasteners or equivalent for proper performance of tool. See page 17-20 for fastener information. Handle the tool carefully. Respect the tool as a working implement and always assume the tool contains fasteners: a. Never use the tool as a toy and engage in horseplay. b. Never aim or point the tool at anyone. The tool may contain fasteners. c. Always keep people and animals at a safe distance from the work area in case of accidental discharge of fasteners. d. Never pull the trigger unless the nose of the tool is against the work surface. e. Do not pull the trigger or depress the contact trip when loading the tool. 3. Insert a stick of fasteners into the magazine. Make sure the pointed ends of the fasteners are loaded with thepoints downward. Also make sure fasteners are not dirty or damaged. Use DeVilbiss fasteners or equivalent for proper fastener performance. Loading the Tool 1. Disconnect air hose. 2. Pull feeder back into "locked" position. PAGE 11 4. Push release button (if equipped) and slide feeder shoe forward. Release Button Feeder OPERATING THE TOOL READ THIS MANUAL AND UNDERSTAND ALL SAFETY WARNINGS AND INSTRUCTIONS BEFORE OPERATING TOOL. Protect your eyes and ears. Wear Z87 safety glasses with side shields. Wear hearing protection. Employers and users are responsible for ensuring the user or anyone near the tool uses the prescribed safety equipment. Disconnect tool from air compressor before adjusting, clearing jams, servicing, relocating and during non-operation. Failure to do so could result in serious injury or property damage. NOTE Check and replace any damaged or worn components on the tool. The safety warning labels on the tool must also be replaced if they are not legible. 1. Add one drop of DeVilbiss AC230 Air Tool Oil, high speed spindle oil, such wood. If the fasteners do not achieve the as Unocal RX22, or 3-in1 oil into the desired penetration, adjust the air air inlet. pressure to a lower or higher setting until the desired penetration is achieved. 2. Connect the Tool to the air supply. Do not exceed the maximum operating 3. Regulate the air pressure to obtain a PSI at the tool. minimum of 75 PSI at the tool. NOTE: When loaded with Brad Nails, the 4. Set air pressure regulator to 75 PSI and NBSNC2x4 will leave a 1/4 inch indention. test for proper fastener penetration by Tilting the tool to the left 10° will eliminate driving fasteners into a sample piece of the indention. PAGE 12 CLEARING A JAM FROM THE TOOL Disconnect tool from air compressor before adjusting, clearing jams, servicing, relocating and during non-operation. FASTENER JAMMED IN FASTENER DISCHARGE AREA: 1. Disconnect tool from air hose. 2. NF2502X4, NB1252X4, NB2002X4, 3. Remove fasteners from magazine. 4. NF2502X4, SNC100...
Эта инструкция также подходит к моделям:Строительные пистолеты - 2by4 Contractor Series (745.96 kb)
Строительные пистолеты - 2by4 MG-NS2X4A (745.96 kb)
Строительные пистолеты - 2by4 NB1252X4 (745.96 kb)
Строительные пистолеты - 2by4 NB2002X4 (745.96 kb)