Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
* Note: Specifications may differ from country to country. WARNING: For your personal safety, READ and UNDERSTAND before using. CAW= TUECC I~ICTRIIrTinhic Erin EI ITI IRE RCCCRCMPC IMPORTANT SAFETY INSTRUCTIONS WARNING: WHEN USING THIS TOOL, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. .For personal safety and proper operation and maintenance of the tool, read this instruction manual carefully before using the tool. Always wear safety glasses to protect your eyes from dust or nail injury. The safety glasses should conform with the requirements of ANSI 287.1 - 1979. WARNING: It is an employer’s responsibility to enforce the use of safety eye protection equipment by the tool operators and by other persons inthe immediate working area. .Wear hearing protection to protect your ears against exhaust noise and head protection. Also wear light but not loose clothing. Sleeves should be buttoned or rolled up. No necktie should be worn. Rushing the job or forcing the tool is dangerous. Handle the tool carefully. Do not operate when under the influence of alcohol, drugs or the like. *General Tool Handling Guidelines: 1. Always assume that the tool contains fasteners. 2. Do not point the tool toward yourself or anyone whether it contains fasteners or not. 3.Do not activate the tool unless the tool is placed firmly against the workpiece. 4. Respect the tool as a working implement. 5. No horseplay. 6. Do not hold or carry the tool with a finger on the trigger. 7. Do not load the tool with fasteners when any one of the operating controls is activated. 8. Do not operate the tool with any power source other than that specified in the tool operating/safety instructions. *An improperly functioning tool must not be used. I M .Sparks sometimes fly when the tool is used. Do not use the tool near volatile, flammable materials such as gasoline, thinner, paint, gas, adhesives, etc.; they will ignite and explode, causing serious injury. *The area should be sufficiently illuminated to assure safe operations. The area should be clear and litter- free. Be especially careful to maintain good footing and balance. I II .Only those involved in the work should be in the vicinity. Children especially must be kept away at all times. .There may be local regulations concerning noise which must be complied with by keeping noise levels within prescribed limits. In certain cases, Shutter shutters should be used to contain noise. Do not play with the contact element: it prevents accidental discharge, so it must be kept on and not removed. Securing the trigger in the ON po- sition is also very dangerous. Never attempt to fasten the trigger. Do not operate a tool if any portion of the tool operating controls is inoperable, disconnected, altered, or not working properly. .Operate the tool within the specified air pressure of 4.5 -8.5 kgf/cm'G (65 -120 PSIG) for safety and longer tool life. Do not exceed the recom- 0.5kgf/cm2G 8.5 kgf/cm2G I mended max. operating pressure of 8.5 (120 PSIG) (120 PSIG) kgf/cm'G (120 PSIG). The tool should not be connected to a source whose pressure potentially exceeds 14.0 kgf/cm*G(200 PSIG). *Never use the tool with other than compressed air. If bottled gas (carbon dioxide, oxgen, nitro- gen, hydrogen, air, etc.) or combustible gas (hydrogen, propane, acetylene, etc.) is used as a power source for this tool, the tool will explode and cause serious injury. *Always check the tool for its overall condition and loose screws before operation. Tighten as required. Make sure all safety systems are inworking order before operation. The tool must not operate if only the trigger is pulled or if only the contact arm is pressed against the wood. It must work only when both actions are performed. Test for pos- sible faulty operation with nails unloaded and the pusher in fully pulled position. COMPRESSED AIR *Make sure that the trigger is locked when the I change lever is set to the LOCK position. *Check walls, ceilings, floors, roofing and the like carefully to avoid possible electrical shock, gas leakage, explosions, etc. caused by striking live wires, conduits or gas pipes. I I Live wire Gas Use only nails specified in this manual. The use of any other nails may cause malfunction of the tool. Do not permit those uninstructed to use the tool. I Make sure no one is nearby before nailing. Never attempt to nail from both the inside and outside at the same time. Nails may rip through and/or fly off, presenting a grave danger. *Watch your footing and maintain your balance with the tool. Make sure there is no one below when working in high locations, and secure the air hose to prevent danger if there is sudden jerking or catching. On rooftops and other high locations, nail as you move forward. It is easy to lose your footing if you nail while inching backward. When nailing against perpendicular surface, nail from the top to the bottom. You can per...
Эта инструкция также подходит к моделям:Строительные пистолеты - AN942 (1.23 mb)