Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Respect the tool as a working implement; no horseplay. Always keep others at a safe distance from the work area in case of accidental discharge of fasteners. Do not point the tool toward yourself or anyone whether it contains fasteners or not. Accidental triggering of the tool could result in death or serious personal injury. Do not drive a fastener on top of other fasteners. The fastener could glance and cause death or a serious puncture wound. Do not operate or allow anyone else to operate the tool if any warnings or warning labels are not legible. Warnings or warning labels are located on the tool magazine and body. Do not drop or throw the tool. Dropping or throwing the tool can result in damage that will make the tool unusable or unsafe. If the tool has been dropped or thrown, examine the tool closely for bent, cracked or broken parts and air leaks. STOP and repair before using or serious injury could occur. Caution indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury. ! CAUTION Air compressors providing air to the tool should follow the requirements established by the American National Standards Institute Standard B19.3-1991; Safety Standard for Compressors for Process Industries. Contact your air compressor manufacturer for information. Operating The Tool LUBRICATION This tool requires lubrication before using the tool for the first time and before each use. If an inline oiler is used, manual lubrication through the air inlet is not required on a daily basis. The work surface can become damaged by excessive lubrication. Proper lubrication is the owner’s responsibility. Failure to lubricate the tool properly will dramatically shorten the life of the tool and void the warranty. 1. Disconnect the air supply from the tool to add lubricant. 2. Turn the tool so the air inlet is facing up. Place 4-5 drops of 30 W non-detergent oil into air inlet. Do not use detergent oils, oil additives, or air tool oils. Air tool oils contain solvents which will damage the tool's internal components. NOTICE Do not make any modifications to the tool without first obtaining written approval from Campbell Hausfeld. Do not use the tool if any shields or guards are removed or altered. Do not use the tool as a hammer. Personal injury or tool damage may occur. Avoid long extended periods of work with the tool. Stop using the tool if you feel pain in hands or arms. Always check that the Work Contact Element (WCE) is operating properly. A fastener could accidentally be driven if the WCE is not working properly. Personal injury may occur (See "Checking the Work Contact Element" Section). Disconnect air supply and release tension from the pusher before attempting to clear jams because tools can be ejected from the front of the tool. Personal injury may occur. Notice indicates important information, that if not followed, MAY cause damage to equipment. Avoid using the tool when the magazine is empty. Accelerated wear on the tool may occur. Clean and check all air supply hoses and fittings before connecting the tool to an air supply. Replace any damaged or worn hoses or fittings. Tool performance or durability may be reduced. NOTICE Operating Instructions Model HDN23200 O I L ! WARNING Recommended Hookup Quick Plug Quick Coupler Air Hose Quick Plug (Optional) Quick Coupler (Optional) Oiler Regulator Filter OIL Modelo # Longitud Calibre Clavos por Clavos por del cuerpo Acabado Cabeza Union linea Caja FB001600 15,9mm (5/8”) Calibre 18 Galvanizado De puntilla/Cafe Adhesivo 100 5000 FB002000 19,1mm (3/4”) Calibre 18 Galvanizado De puntilla/Cafe Adhesivo 100 5000 FB002500 25,4mm (1”) Calibre 18 Galvanizado De puntilla/Cafe Adhesivo 100 5000 FB003000 31,8mm (11.4”) Calibre 18 Galvanizado De puntilla/Cafe Adhesivo 100 5000 Clavos Estos clavos para acabado de Campbell Hausfeld los puede comprar en su tienda mas cercana. Si necesita ayuda para encontrar un articulo, comuniquese al 1-800-543-6400. Los clavos de Campbell Hausfeld cumplen o exceden el estandar ASTM F1667 Informacion de intercambio Los clavos usados con la HDN23200 tambien se pueden usar con las clavadoras : Bostitch T31-1, T29-30, BT-35, Duofast BB4440, Hitachi NT45A , Paslode 2138-F18 , Porter Cable BN125, BN200, Sears 18309, y Senco SLP20, LS2, LS5. Grapas Estas grapas para acabado de Campbell Hausfeld los puede comprar en su tienda mas cercana. Si necesita ayuda para encontrar un articulo, comuniquese al 1-800-543-6400. Las grapas de Campbell Hausfeld cumplen o exceden las especificaciones Federales FF-N-105B. Informacion de intercambio Las grapas usadas con la HDN23200 tambien se pueden usar con las grapadoras: Senco LN4450, SJS-LR, SKS L11-15, Hitachi N3804A, Duofast BN-1832S, KN-1848, ST-18, Stan-Tech SDS 18-14, Atro Minor 90/30, 90/32, 90/40, y Porter Cable NS100. Calibre Fusion de Grapas Grapas Modelo # Longitud de la grapa Corona Punta Acabado la linea por linea por caja FN158K00 12,7mm (1/2”) Calibre 18 6,4mm(...