Оценок - 5, средний балл: 3.6 ( )

Производитель: Equator Размер: 1.27 mb Название файла: Язык инструкции:

Installation -e.g. improper hook-up or leveling . Maintenance -e.g. cleaning of air and/or water filter . Damage -e.g. Replacing broken door handle Most work is covered. The defining factor is, has the machine malfunctioned (Equator is responsible) or has the customer omitted or done something to cause machine to malfunction (customer is responsible). Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. 1 WARRANTY SERVICE This warranty is given by: Equator Corporation, Equator Plaza, 2801 W. Sam Houston Pkwy. N., Houston, TX 77043-1611. Service under this warranty must be obtained by the following steps, in order: Call an Equator Corporation Authorized Service Agent (obtain number of nearest agent from your dealer or by calling Equator Service at 1-800-776-3538). Under normal circumstances, Service will be provided during regular business hours (9:00 a.m. to 5:00 p.m. weekdays). GENERAL Since it is responsibility of the consumer-owner to establish the warranty period by verifying the original purchase date, Equator Corporation recommends that a receipt, delivery slip or some other appropriate payment record be kept for that purpose. Remember to send in your Warranty Registration Card so that a proof of your purchase exists with Equator. This warranty gives you specific legal rights, and you may also have other rights which vary from State to State. Corporate Office EQUATOR CORPORATION Equator Plaza 2801 W. Sam Houston Pkwy. N. Houston, TX 77043-1611 Tel: 713-464-3422 -Fax: 713-464-2151 Tel: 800-776-3538 Troubleshooting Problem Possible Cause Repair procedure Installation 1. Machine vibrating or vibrating noise 1a. Shipping brackets not removed 1a. Open back of machine, remove 4 shipping brackets connecting cabinet to drum 1b. Machine not leveled 1b. Adjust front leveling legs and tighten locknuts 1c. Machine installed on uneven floor 1c. Adjust leveling legs 1d. Machine installed on wood floor 1d. Move machin to a more appropriate location or install underlayment 1e. Rubber cap missing from rear foot 1e. Install new ribber foot 2. Water leaking from door 2a. Door not screwed in properly 2a. Screw door in properly 2b. Door not aligned 2b. Align door and screw in properly/Replace with new door 2c. Boot leaking 2c. Change boot (porthole diaphrgm) Problem Possible Cause Repair Procedure Wash Cycle 1. Won't fill 1a. No power input. 1a. Check that the cord is plugged in, and circuit breaker or fuse is OK. Test unit power switch. 1b. No water pressure. 1b. Check that fill hoses are connected that the water supply is turned on, and hoses are not kinked. 1c. Drain outlet below 20" (water siphoning out) 1c. Route drain hose through a clamp on the rear of the machine, at least 24" above the floor. 1d. Door not closed tightly 1d. Close door firmly, so that it latches. 1e. Door Switch/Lock. 1e. Set to start of regular wash cycle. Test for 115 vac between the common (low) side of the water inlet valves & terminal 21 of the pressure switch. If not present, the door switch may be defective. 1f. Pressure Switch. (test with no water in the tub) Set to start of the regular wash cycle. Test for 115 vac between the common (low) side of the water inlet valves and terminal 22 of the pressure switch. If not present, the pressure switch may be defective. 2 Problem Possible Cause Repair Procedure 1g. Timer 1g. Set to start of regular wash cycle. Test for 115 vac between high side of hot and cold water inlet valves and common (low) side of water inlet valves. If not present, the timer may be defective. 1h. Temperature Selector Switch 1h. Set to Start of the regular wash cycle. Set water temperature selector to WARM/COLD. Test for 115 vac between high side of hot and cold water inlet valves and common (low) side of water inlet valves. If not present the selector switch may be defective . 1i. Water inlet valves. 1i. If 115 vac is present across a water inlet valve coil and water pressure is present, the machine should fill. If not, the valve may be defective. 2. Fills, won't agitate 2a. Belt. 2a. Check belt, adjust tension. 2b. Electronic Control Module 2b. Test signals at the Control Module. See Testing the Electronic Control Module. If correct, replace the Control. If test on terminals 1 to 7 fail, replace timer. If tests on terminal 8, 9, 12 through 15 fail, replace motor. 2c. Motor 2c. Check motor resistance. See Testing Drive motor. 3. Won't drain 3a. Filter 3a. Remove, clean, and replace filter. 3b. Drain hose 3b. Check for kinks or blockage. 3c. Drain 3c. Drain standpipe inlet more than 36" above the floor. Blocked drain. (direct connection) 3d. Pump 3d. With power off, run pump cooling impeller manually to check for jamming. If pump does not turn freely, disassemble, remove foreign objects, and reassemble. 3e. Timer 3e. Set timer to REGULAR SPIN. Test for 115 vac across the pump terminals. If present, the pump may be defective. If...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: