Оценок - 2, средний балл: 4 ( )

Производитель: Alliance Laundry Systems Размер: 1.22 mb Название файла: Язык инструкции:

Ideally, the water should empty through a vented pipe directly into a sump or floor drain. Figure 33 shows drain line and drain trough configurations. Figure 33 CFS490N 1 Water Inlet 2 Water Inlet Air Gap 3 Drain Pipe 4 1-Inch Minimum Waste Line Air Gap (Per local code) 5 Steel Grate 6 Drain Trough 7 Strainer 8 Waste Line 4 REAR OF MACHINE 3 5 6 1 7 8 2 A flexible connection must be made to a vented or air gap drain system to prevent an air lock and to prevent siphoning. If proper drain size is not available or practical, a surge tank is required. A surge tank in conjunction with a sump pump should be used when gravity drainage is not possible, such as in belowground- level installations. Before any deviation from specified installation procedures is attempted, the customer or installer should contact the distributor. Increasing the drain hose length, installing elbows, or causing bends will impair washer-extractor performance. Refer to Table 3 for capacity-specific drain information. Installation of additional washer-extractors will require proportionately larger drain connections. Refer to Table 4. 44 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 9001000 Installation Drain Information Model 18 25 33 35 40 55 75 100 135 165 200 Drain connection size, ID 2 in. (51 mm) 2 in. (51 mm) 2 in. (50 mm) 2 in. (51 mm) 2 in. (50 mm) 3 in. (76.2 mm) 3 in. (76.2 mm) 3 in. (76.2 mm) 3 in. (76.2 mm) 3 in. (76.2 mm) 3 in. (76.2 mm) Number of drain 1 1 1 1 1 1 1 1 1 2 2 outlets Drain flow 32 32 21.13 32 21.13 73 73 73 73 73 73 capacity gal/min gal/min gal/min gal/min gal/min gal/min gal/min gal/min gal/min gal/min gal/min (120 (120 (160 (120 (160 (280 (280 (280 (280 (280 (280 l/min) l/min) l/min) l/min) l/min) l/min) l/min) l/min) l/min) l/min) l/min) Recommended 2.5 ft3 3.3 ft3 5.1 ft3 5.8 ft3 6.4 ft3 8.3 ft3 11 ft3 16 ft3 20 ft3 24 ft3 31.8 ft3 drain pit (72 l) (95 l) (1451) (165 l) (1811) (235 l) (304 l) (455 l) (575 l) (679 l) (9001) size Table 3 Drain Line SizingMinimum Drain ID Model Number of Machines 1 2 3 4 5 6 7 18 2 in. (51 mm) 3 in. (76.2 mm) 3.5 in. (88 mm) 4 in. (102 mm) 4.5 in. (114 mm) 5 in. (124 mm) 5.5 in. (140 mm) 25 2 in. (51 mm) 3 in. (76.2 mm) 3.5 in. (88 mm) 4 in. (102 mm) 4.5 in. (114 mm) 5 in. (124 mm) 5.5 in. (140 mm) 33 2 in. (51 mm) 3 in. (76.2 mm) 3.5 in. (88 mm) 4 in. (102 mm) 4.5 in. (114 mm) 5 in. (124 mm) 5.5 in. (140 mm) 35 2 in. (51 mm) 3 in. (76.2 mm) 3.5 in. (88 mm) 4 in. (102 mm) 4.5 in. (114 mm) 5 in. (124 mm) 5.5 in. (140 mm) 40 2 in. (51 mm) 3 in. (76.2 mm) 3.5 in. (88 mm) 4 in. (102 mm) 4.5 in. (114 mm) 5 in. (124 mm) 5.5 in. (140 mm) 55 3 in. (76.2 mm) 4 in. (102 mm) 5 in. (131 mm) 6 in. (152 mm) 6.7 in. (170 mm) 7.3 in. (186 mm) 8 in. (203 mm) 75 3 in. (76.2 mm) 4 in. (102 mm) 5 in. (131 mm) 6 in. (152 mm) 6.7 in. (170 mm) 7.3 in. (186 mm) 8 in. (203 mm) 100 3 in. (76.2 mm) 4 in. (102 mm) 6 in. (152 mm) 7 in. (177.8 mm) 8 in. (203 mm) 10 in. (254 mm) 12 in. (305 mm) 135 3 in. (76.2 mm) 4 in. (102 mm) 6 in. (152 mm) 7 in. (177.8 mm) 8 in. (203 mm) 10 in. (203 mm) 12 in. (305 mm) 165 3 in. (76.2 mm) 4 in. (102 mm) 6 in. (152 mm) 7 in. (177.8 mm) 8 in. (203 mm) 10 in. (203 mm) 12 in. (305 mm) 200 3 in. (76.2 mm) 4 in. (102 mm) 6 in. (152 mm) 7 in. (177.8 mm) 8 in. (203 mm) 10 in. (203 mm) 12 in. (305 mm) Table 4 9001000 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 45 Installation Water Connection WARNING To avoid personal injury, recommended inlet water temperature should be nohigher than 125° Fahrenheit (51° Celsius). W709 The 18-135 models are delivered with hoses with 3/4 inch hose connectors. The 165 model is delivered with 3 x 1 inch and 1 x 3/4 inch hose connectors. These hoses fit the water inlet valves of the machine and the main water inlet taps. To ensure the optimal functioning of the water inlet valves, the water pressure on the inlet should be between 30-85 psi (2-5.7 bar). If the pressure is too low, the cycle time will increase considerably. In case of boiler fed machines, a maximum of hot water of 194°F (90°C) should be available: Connections should be supplied by a hot and a cold water line per national and local codes. To connect water service to machine with rubber hoses, use the following procedure: 1. Before installing hoses, flush the water system for at least two minutes. 2. Check filters in the washer-extractor’s inlet hoses for proper fit and cleanliness before connecting. 3. Hang the hoses in a large loop, do not allow them to kink. If additional hose length is needed use flexible hoses with screen filters. Each hose should have a screen filter installed to keep rust and other foreign particles out of the water inlet valves. Pressure of 30-85 psi (2-5.7 bar) provides best performance. Although the washer-extractor will function at lower pressures, increased fill times will occur with some loss of supply flushing. Suitable air cushions should be installed in supply lines to prevent “hammering.” Water Supply Inform...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: