Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
After cleaning, cover the unpainted surfaces with a good quality paste wax. FOR YOUR OWN SAFETY, DO NOT CONNECT THE TOOL TO THE POWER SOURCE UNTIL THE TOOL IS COMPLETELY ASSEMBLED, AND YOU READ AND UNDERSTAND THE ENTIRE OWNER’S MANUAL. CARTON CONTENTS 10 8 9 7 5 6 3 1 2 4 11 12 13 14 15 16 17 Fig. 4 1. Headstock 2. Lathe Bed 3. Live Center 4. Leg Insert (4) 5. Spindle Wrench 6. Knockout Bar 7. 5/32” Allen Wrench 8. Drive Center 9. Tool Rest 10. Tailstock 11. 1/4-20 x 1/2” Button Head Screw (4) 12. 1/4-20 Flange Nut (4) 13. 3/8” Flat Washer (12) 14. 3/8” Lockwasher (12) 15. 3/8-16 x 3/4” Hex Head Bolt (12) 16. End Cap (2) 17. Pedestal (2) 7 ASSEMBLY ATTACHING LATHE BED TO PEDESTALS 1. Remove tailstock, headstock, and tool rest from the lathe bed. NOTE: See “ADJUSTING HEADSTOCK AND TAILSTOCK” and “TOOL REST” for removal/installation instructions. 2. Set pedestals exactly 58” apart (Fig. 5). 3. Because of the weight, use an assistant to place the lathe bed on top of the pedestals. Make sure that the holes in the lathe bed are aligned with the holes in the tops of the pedestals (Fig. 6) A and B. 4. Attach the lathe bed to the pedestals, using the twelve 3/8-16 x 3/4” Hex Head bolts and lock washers. The hole in the pedestal (C) Fig.6 can be used to fill the pedestal with sand or concrete to provide more ballast. NOTE: If sand is used, pour a small amount of concrete or similar material in the pedestal to prevent sand leakage through the seams. In addition to showing the location of the bolt (A) Fig. 7 also shows that additional ballast can be added in the lathe bed (B). Steel bars, or other heavy material can be inserted into the lathe bed to provide more weight. NOTE: Use a good quality furniture wax on the lathe bed (C) Fig. 7 to allow for smoother movement of the headstock, tool rest, and tailstock and to prevent rust. ATTACHING END CAPS Attach the end caps, (A) Fig. 8, to both ends of the lathe with 1/4-20 x 1/2” button head screws (A) Fig. 9 (outside) the lathe bed through the end caps to the 1/4-20 flange nut (inside) (B) Fig. 8 . NOTE: The flange nut can easily be dropped while attaching the endcap. To prevent loss of the flange nut, use a small piece of cardboard or other material to cover the hole in the pedestal. 58” Fig. 5 Fig. 6 A B B C B A C Fig. 7 A B A B Fig. 8 Fig. 9 8 ATTACHING LEG INSERTS The lathe is supplied with four leg inserts, one of which is shown (A) Fig. 10. To attach the leg inserts to the pedestals, place one side in the hole provided and gently tap the other side, top, and bottom with a rubber mallet (B) Fig. 10. Attach the Headstock (D) Fig. 11, Tool Rest (E) Fig. 11, and Tailstock (F) Fig. 11 to the lathe bed (G) Fig. 11. Notice the tool and centers storage areas located at (H) Fig. 11, and brackets on the pedestals to accept a 2 x 12” shelf (not supplied) (I) Fig. 11. If additional stability is desired, insert 4 x 4 lumber (A) Fig 11 into feet of pedestal (B) Fig. 11. Secure the lumber to the pedestal with four 3/8-16 bolts (not supplied) in holes (C) Fig. 11 (two of which are shown). Fasten the 4 x 4’s to the floor. A B Fig. 12 C A B D Fig. 13 A B Fig. 10 B A A C Fig. 11 D E F G H C B I HEADSTOCK SPUR CENTER The spur center (A) Fig.12 is equipped with a No. 2 Morse Taper shank. Inserted this shank into the headstock spindle (B). NOTE: Before inserting the spur center (A), clean both the shank of the spur center and the inside of the headstock spindle to remove any grease or debris. To remove the tapered shank spur center (A) Fig. 13, from the headstock spindle (B) Fig. 13, use the knockout bar (C) Fig. 13 (supplied) through the hole (D) in the opposite end of the spindle. IMPORTANT: NEVER DRIVE THE WORKPIECE INTO THE SPUR CENTER WHEN IT IS MOUNTED IN THE HEADSTOCK. See instructions on setting the spur center into the workpiece in the “OPERATION“ section of this manual under “CENTERING THE WORK.” 9 TAILSTOCK LIVE CENTER The tailstock live center (A) Fig. 14, supplied with your lathe, is equipped with a No. 2 Morse Taper shank. NOTE: Before inserting the live center, clean both the shank and the inside of the tailstock to remove any grease or debris. To remove the live center (A) from the tailstock spindle (B), use the knockout bar (C) Fig. 14 (supplied) through the hole (D) in the opposite end of the spindle. ADJUSTING CLAMPS ON THE HEADSTOCK AND TAILSTOCK The headstock and tailstock can be moved along the lathe bed. A downward push on the handle (A) Fig. 15 (tailstock shown) locks the mechanism, while an upward movement of the handle releases the securing action. The clamps are pre-set at the factory. However, should either need adjusting, use a 11/16” wrench (B) Fig. 15 to slightly loosen or tighten the two nuts (C) Fig. 15 shown here on the tailstock. NOTE: Be certain that both nuts are tightened, or loosened, equally. NOTE: Clamp headstock and tailstock firmly while operating the lathe. TOOL REST The tool rest (A) and tool rest base (B) are shown in Fig. 16. To position the ...
Эта инструкция также подходит к моделям:Станки - 46-745 (1.42 mb)
Станки - 46-765X (1.42 mb)