Оценок - 2, средний балл: 3 ( )

Производитель: Sony Размер: 179.73 kb Название файла: Язык инструкции:

Tips • Movies are best enjoyed in a room that produces no echoes (as in one with surrounding curtains). • Music (especially classical music) is best enjoyed in a room that produces some echo. 15. 25. 1 2 33 Screws Bottom view 1 Pass the speaker cord into the hole on the back of the base and out from the hole at the bottom of the mount. 2 Secure the center speaker to the mount with the supplied screw. 3 Adjust the angle of the speaker stand. Loosen the two screws under the base to adjust the angle, then tighten them again afterwards. SA-VE305 Attach the supplied foot pads to the bottom of the center speaker, one in each of the four corners. Set the speaker firmly on top of the TV set, then make sure it is completely level. Foot pads continued Positioning the speakers (continued) Setting up other WS-FV10 WS-TV10 WS-WV10 (for rear speakers) SA-VE505/VE502 only You can attach the supplied foot pads to the bottom of the speakers, one in each corner. SA-VE305/VE302 only You can hang or install the front (and rear) speakers on a wall using hooks or nuts (commercially available). Hook 60 mm Nuts (M5) Note You are responsible for the proper selection and use of mounting hardware that you purchase at a hardware store, and for the proper and safe mounting of the speakers. Tip (for SA-VE505/VE305) Listening to the sound SA-VE505/VE502 SA-VE305/VE302 speakers For greater flexibility in the positioning of the speakers, use the optional WS-FV10, WS-TV10, or WS-WV10 speaker stand (available only in certain countries). ON/STANDBY POWER U !indicator !!indicator ! First, turn down the volume on the amplifier. The volume should be set to minimum before you begin playing the program source. 1 Turn on the amplifier and select the program source. 2 Press !on the subwoofer. The !indicator on the subwoofer lights up green. 3 Play the program source. Power turns on and off automatically — Auto power on/off function (SA-VE505/VE502 only) When the subwoofer is on (i.e, the ! indicator lights up green) and there is no signal input for a few minutes, the ! indicator changes to red and the subwoofer enters power saving mode. While in this mode a signal is input to the subwoofer, the subwoofer automatically turns on (auto power on/off function). To turn this feature off, slide the POWER SAVE switch on the rear panel to OFF. AUTO OFF POWER SAVE Note If you turn down the volume level of the subwoofer too low, the auto power on/off function may activate, causing the subwoofer to enter power saving mode. The height of the front speakers should be adjusted to about the center of the TV screen. Adjusting the sound Slight adjustments to the system can enhance your sound enjoyment. Adjusting the subwoofer SA-VE505/VE502 ON/STANDBY LEVEL MODE MIN MAX MOVIE MUSIC LEVEL MODE 1 Set MODE according to the program source as follows: Source MODE DVD, LD, video cassette MOVIE or other video source MD, CD, cassette tape MUSIC or other audio source 2 Rotate LEVEL to adjust the volume. Set the volume level to suit the program source. Notes • Some amplifier functions for enhancing the sound may cause distortion in the subwoofer. If such distortion occurs, turn off those functions. • To enjoy high-quality sound, do not turn the subwoofer volume too high. • To increase the bass sound from the subwoofer, connect the system using “Hookup B” (see page 5). SA-VE305/VE302 POWER LEVEL CUT OFF FREQ PHASE MIN MAX 50Hz 200Hz .NORMAL .REVERSEU LEVEL CUT OFF FREQ PHASE 1 Rotate CUT OFF FREQ to set a cut-off frequency of 100 Hz to 150 Hz (or between 1 o’clock and 3 o’clock position, in terms of position). For Dolby Digital (AC-3), set the cut-off frequency to the maximum level (200 Hz). 2 Rotate LEVEL to adjust the volume. Set the volume level to suit the program source. 3 Press PHASE to select the phase polarity (NORMAL or REVERSE). Set PHASE to NORMAL when Dolby Digital (AC-3) is on. Tip The proper phase polarity depends on the location of a subwoofer or adjustment of the cut-off frequency. Try both settings and select the one that suits your listening taste. Notes • Some amplifier functions for enhancing the sound may cause distortion in the subwoofer. If such distortion occurs, turn off those functions. • To enjoy high-quality sound, do not turn the subwoofer volume too high. • To increase the bass sound from the subwoofer, connect the system using “Hookup B” (see page 5). continued Adjusting the sound (continued) For the Dolby Pro Logic Setting your amplifier to enjoy movies (SA-VE505/VE305 only) For the Dolby Digital (AC-3) If your amplifier is connected internally or externally with a Dolby Digital (AC-3) processor, you should use the some setup menus in the amplifier to specify the parameters of your speaker system. See the table below for the proper settings. For details on the setting procedure, refer to the manual that was provided with your amplifier. When “Hookup A” is used (Speaker setup) For Set to Front speakers SMALL Center speaker SMALL Rear speakers SMAL...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: