Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
SAVE THESE INSTRUCTIONS Work Area Keep your work area clean and well lit. 1. Cluttered benches and dark areas invite accidents. Keep children and visitors away while installing and operating. 2. Distractions can cause you to lose control. Never allow children to play with the Oooga Horn. Avoid body contact with grounded surfaces such as pipes, radiators, ranges, 3. and refrigerators. There is an increased risk of electric shock if your body is grounded. Do not expose the Oooga Horn to rain or wet conditions. 4. Water entering the Oooga Horn will increase the risk of electric shock. Use safety equipment. 5. Dust mask, nonskid safety shoes or hearing protection must be used for appropriate conditions. Always wear ANSI-approved safety goggles and a dust mask/respirator when installing this item. Store idle equipment out of reach of children and other untrained persons. 6. Tools are dangerous in the hands of untrained users. Check for breakage of parts and any other condition that may affect the Oooga 7. Horn’s operation. If damaged, have the tool serviced before using. Service must be performed only by qualified repair personnel. 8. Service or maintenance performed by unqualified personnel could result in a risk of injury. Maintain labels and nameplates on the Oooga Horn. 9. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. WARNING: The brass components of this product contain lead, a chemical 10. known to the State of California to cause birth defects (or other reproductive harm). (California Health & Safety code § 25249.5, et seq.) Exposure to noise levels over 85 dB is hazardous to hearing. 11. Always wear ANSI approved hearing protection when operating the Oooga Horn. Never use Horn in close proximity to people or animals, as the decibel level may cause hearing damage. Before using the Oooga Horn, check and comply with local standards for 12. noise pollution levels. Unpacking When unpacking, check to make sure that the item is intact and undamaged. 1. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. Assembly Instructions Caution: Installation should be completed by a qualified technician. Before attempting installation of the Oooga Horn, turn off the ignition, shift the gear 1. into park (for automatic transmissions) or reverse (for manual). Remove the car keys from the ignition switch and allow the engine to cool. Place wheel chocks on both sides of at least 2 wheels. Disconnect the vehicle’s battery. Make sure the engine and engine compartment are cool before beginning work. Lift the vehicle hood and find a suitable location to mount the Oooga Horn (1). This 2. location must shelter the Oooga Horn and Compressor from incoming rain, road water, and mud splash from under the vehicle. Do not mount the Horn near hot engine components or where it may come into direct contact with hot surfaces or any moving parts. Mount the Oooga Horn to the vehicle’s chassis using the Nut and Bolt (2). The Oooga 3. Horn (1) should be pointing forward and slightly down for maximum efficiency. A hole may need to be drilled in the chassis frame to accomplish this. Before drilling the hole, make sure the drill’s path will not come in contact with hidden wiring or any other obstructions or vehicle components. Tighten the Nut securely. Mount the Electric Relay (not included), as shown in the Wiring Diagrams, to the 4. chassis frame near the Oooga Horn using a Bolt and Nut (not included). Tighten securely. Make the connections to the Oooga Horn (1) and the Electric Relay (not included) 5. as shown on the Mounting and Wiring Diagrams. Always use terminal connectors (not included) on all connections. Connect the terminal on the Electric Relay to a 30A fused circuit. Note: Most vehicles use a negative ground, but some vehicles employ a positive ground. If this is the case, refer to Positive Ground Wiring Diagram. Pay attention to polarity. Negative Ground Wiring Diagram Electric Relay8788513085Existing vehicle fused circuitPushbutton Horn Switchnot includedConnection is to the line positive “+” point of the original horn+12 VDC30 A REV 08a Positive Ground Wiring Diagram Electric Relay8788513085Existing vehicle fused circuitPushbutton Horn Switchnot includedConnection is to the line positive “+” point of the original horn-12 VDC+12 VDC30 A INSPECTION, MAINTENANCE, AND CLEANING 1. WARNING! Make sure the ignition of the vehicle is in the “OFF” position and that the tool is disconnected from the electrical outlet before performing any inspection, maintenance, or cleaning procedures. BEFORE EACH USE, inspect the general condition of the tool. Check for loose 2. screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, have the problem corrected before furt...