Оценок - 3, средний балл: 3.3
(
)
)
|
Фото и характеристики HTC Wildfire S |
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Notification LED 2. Proximity sensor 3. Earpiece 4. Touch screen 5. Home 6. Menu 7. Back 8. Search Getting started Left panel 1. VOLUME UP 2. VOLUME DOWN 3. USB connector Back panel 1. LED flash 2. 5 megapixel camera 3. Speaker 4. Microphone 5. Lanyard hole Top panel 1. 3.5mm headset jack 2. POWER 10 Getting started Back cover Removing the back cover Remove the back cover to access the battery compartment, SIM card slot, and storage card slot. 1. Turn off HTC Wildfire S and hold it securely with the front facing down. 2. With your finger, pry open the back cover from the small opening near the POWER button. Replacing the back cover 1. Press the bottom part of the back cover first by aligning into the openings located at the bottom part of the back of HTC Wildfire S. 2. Press the sides and the top part of the back cover down to lock the cover into place. You will hear a click when the back cover is locked in place. SIM card The SIM card contains your phone number, service details, and phonebook/message memory. Both 1.8V and 3V SIM cards can be used. Some legacy SIM cards may not function with HTC Wildfire S. You should consult with your mobile operator for a replacement SIM card. There may be fees for this service. Inserting the SIM card 1. Take the back cover off. 2. Remove the battery. Getting started 3. Slide the SIM card holder in the direction of “OPEN” (etched on the SIM card holder), and then flip it open. 4. Insert the SIM card with its gold contacts facing down and its cut-off corner facing out the SIM card slot. 12 Getting started 5. Slide the SIM card completely into the slot. Make sure the SIM card goes through the 2 “guides” on the SIM card slot. 6. Close the SIM card holder and then slide it in the opposite direction of “OPEN” to lock it. Removing the SIM card Make sure to switch off HTC Wildfire S before removing your SIM card. 1. Take the back cover off. 2. Remove the battery. 3. Slide the SIM card holder in the direction of “OPEN”, and then flip it open. 4. Slide the SIM card out from the SIM card slot. 13 Getting started Storage card Inserting the storage card 1. Take the back cover off. 2. Insert the microSD card into the storage card slot with its gold contacts facing down and push it until it clicks into place. Removing the storage card If HTC Wildfire S is on you must first "unmount" the storage card before removing it to prevent corrupting or damaging the files in the storage card. 1. Take the back cover off. 2. Slide the storage card out from its slot. Unmounting the storage card When you need to remove the storage card while HTC Wildfire S is on, unmount the storage card first to prevent corrupting or damaging the files in the storage card. 1. From the Home screen, press , and then tap Settings. 2. Tap SD & phone storage > Unmount SD card. 14 Getting started Battery HTC Wildfire S uses a rechargeable battery. How long the battery can last before it needs recharging depends on how you use HTC Wildfire S. Among these are the features and accessories you use (for example, leaving your Bluetooth® connection always on uses more power). Long phone calls and frequent web browsing uses up a lot of battery power. Also, consider your location: poor signal strength from your mobile network and extreme temperature make the battery work harder. Removing the battery thin film Before using HTC Wildfire S for the first time, you need to remove the thin film wrapped around the battery. 1. Take the back cover off. 2. Open the battery compartment door. 3. Pull up on the thin film to remove it. Removing the battery Right after you take HTC Wildfire S out from the box for the first time, don’t forget to remove the thin film wrapped around the battery that’s inside HTC Wildfire S. 1. Take the back cover off. 2. With your thumb or finger, lift the battery from the battery compartment. 15 Getting started Inserting the battery Please use only original batteries that came in the box or replacements that we recommend. 1. Take the back cover off. 2. Insert the battery (with its exposed copper contacts first) into the battery compartment. 16 Getting started Charging the battery The battery is partially charged when shipped. Before you turn on and start using HTC Wildfire S, it is recommended that you charge the battery. Some batteries perform best after several full charge/discharge cycles. • The battery is already installed in HTC Wildfire S when shipped. A thin film is inserted between the battery and the compartment. You need to remove this film before you can charge the battery. • Only the power adapter and USB sync cable provided in the box must be used to charge the battery. • Do not remove the battery from HTC Wildfire S while you are charging it using the power or car adapter. 1. Plug the power adapter into the USB connector. 2. Plug in the power adapter to an electrical outlet to start charging the battery. As the battery is being charged, the notification LED shows a solid orange light. The light turns...