At that time, be sure to sufficiently agitate the mixed gasoline in the container. 4. Do not smoke or place hot object near fuel. 24 Français 7. Carburant_ participer ainsi à la protection de l'environnement et de votre santé. • De l'essence ou de l'huile de basse qualité risque d'endommager les joints, les conduites d'essence ou le réservoir d'essence du moteur. ■ COMMENT OBTENIR UN BON MELANGE OIMPORTANT Faire attention à ne pas trop remuer le carburant. 1. Mesurer les volumes d'esse

2001 Antari Lighting and Effects Ltd. User Manual Antari Snow Machine Congratulations on the purchase of your new ANTARI Snow MACHINE. Introduction Thank you for choosing an ANTARI Snow Machine. You now own a rugged and powerful state- of-the-art machine. Prior to use, we suggest that you carefully read all of the instructions. By following the suggestions found in this user manual, you can look forward to the reliable and satisfactory performance of your ANTARI Snow Machine for years to come. P

1/4 pages 8 & 7. 5 Simplicity Frame. Handle & Shroud Group T 76 Tighten nut (Raf. No. iß) 3 It lbs. max. Clutch lever must pivot frcoly. NOT£ U*e standard hardware torque spec. 173209 unless otherwise noted. A*fe to bottom out In palnut (Ref. No. 23). Mfg. No. 1690901 Ä 1690902 Frame. Handle & Shroud Group Simplicity Ref. No. Part No. Qty. Description 31 1664804 1 SWITCH, Ignition 32 916906 1 LOCKWASHER, Int Tooth. 5/8 33 933741 NUT. Speed, "U", #10 34 1664817 1 GUIDE. Choke K

GEAR) Remove auger/impeller and gear case from housing referring to Auger/Impeller Section. Remove four bolts from bearing flange (Figure 22). Remove flange and gasket. NOTE: At this point bronze gear cannot be removed. Using bearing adjustment wrench remove adjustment plug. While holding input shaft in one hand and using a mallet, strike case until bearing cone pops out of the case. Bronze gear can then be removed from case. After bronze gear is removed, input shaft can then be removed. NOTE: I

Follow with Milk of Magnesia, beaten egg or vegetable oil. Get medical attention immediately! • In case of internal contact, DO NOT induce vomiting! Before tipping unit up onto housing, remove fuel so no spills will occur and remove battery. Ensure unit is secure and will not tip over during maintenance. ALWAYS keep protective structures, guards, and panels in good repair, in place and securely fastened. NEVER modify or remove safety devices. DO NOT change engine governor settings or over-speed

* Cover—on pre-printed two-tone “Swash” stock. Press: * Body—1-color, 2-sided * Cover imprint —1-color, 1-sided Bindery: * Saddle Stitch, Face Trim * Face Trim COVERS: * This file may contain several manuals, which differ only in their covers. * Covers are all present at the beginning of this file. * Back cover for a particular manual is the page IMMEDIATELY AFTER the front cover. • Check the front cover for the individual part number (typically a 171xxxx number). BODY: • The body of the manual

After considerable use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar. BEFORE STARTING THE ENGINE CHECK ENGINE OIL LEVEL The engine on your snow thrower has been shipped, from the factory, already filled with oil. 1. Check engine oil with snow thrower on level ground. 2. Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wa

PRACTICES AND LAWS Practice usual and customary safe working precautions, for the benefit of yourself and others. Understand and follow all safety messages. Be alert to unsafe conditions and the possibility of minor, moderate, or serious injury or death. Learn applicable rules and laws in your area. Always follow the practices set forth in this manual. REQUIRED OPERATOR TRAINING Original purchaser of this unit was instructed by the seller on safe and proper operation. If unit is to be used by so

e Position the snow thrower so the oil drain plug isthe lowest point on the engine_ Remove the oil drain plug and oil fill cap/dipstick, Drain the oil into a suitable container. The oil will drain more freely when warm. Replace the oit drain plug and tighten securely_ Refill the crankcase with SA.E_ 10W-30 motor oi! (or equivalent)., S,A.E. 5W-30 motor oil may be used to make starting easier in areas where the temperature is consistently 20° F. or lower, SPARK PLUG o Make su re the spark plug is