Оценок - 2, средний балл: 5 ( )

Производитель: Ariens Размер: 7.4 mb Название файла: Язык инструкции:

Follow with Milk of Magnesia, beaten egg or vegetable oil. Get medical attention immediately! • In case of internal contact, DO NOT induce vomiting! Before tipping unit up onto housing, remove fuel so no spills will occur and remove battery. Ensure unit is secure and will not tip over during maintenance. ALWAYS keep protective structures, guards, and panels in good repair, in place and securely fastened. NEVER modify or remove safety devices. DO NOT change engine governor settings or over-speed engine. ALWAYS maintain unit in safe operating condition. Damaged or worn out muffler can cause fire or explosion. Keep all hardware properly tightened. Check shear bolts frequently. Maintain or replace safety and instruction labels, as necessary. NEVER store unit with fuel in fuel tank, inside a building where any ignition sources are present such as hot water heaters, space heaters, or clothes dryers. Allow the engine to cool before storing in any enclosure. Shut off fuel and allow engine to cool completely before storing in closed area or covering unit. For extended storage, clean unit thoroughly. See Engine Manual for proper storage. Use only attachments or accessories designed for your unit. Check components frequently. If worn or damaged, replace with manufacturer’s recommended parts. GB - 8 GB - 9 PACKAGE CONTENTS ASSEMBLY Tools Required: • Pliers • Open-End Wrenches: 3/8, 7/16, 1/2, 9/16 in. and/or Adjustable Wrench • Tire Gauge Unfold Handlebar (Figure 4) 1. Remove the lower and loosen the upper wing knobs on the handlebar assembly. 2. Loosen the wing nuts on the shift rod. 3. Put the speed selector lever in the first forward position. 4. Rotate the handlebars into operating position. 5. Install and tighten all wing knobs and wing nuts on the handlebar assembly and shift rod. NOTE: The handlebar has two height positions. Adjust the handlebar height to provide better operator comfort. See Handlebar Height on page 22. ASSEMBLY WARNING: AVOID INJURY. Read and understand the entire Safety section before proceeding. WARNING: Dropping or tipping over boxed unit could result in personal injury or damage to unit. Figure 3 1.Sno-Thro Unit 2.Discharge Chute 3.Chute Rod 4. Literature Pack with Extra Shear Bolts 1 2 4 3 OS7020 1.Wing Knobs 2.Wing Nut 3. Bolt 4. Shift Rod 5.Speed Selector Lever Figure 4 OS7030 1 1 4 2, 3 5 GB - 10 Install Discharge Chute and Discharge Chute Crank (Figure 5) 1. Grease underside of discharge chute ring (if not already greased). 2. Remove mounting hardware from auger housing. 3. Install discharge chute over opening in the auger housing. Finger tighten the mounting hardware removed in step 2. NOTE: Leave discharge chute pedestal loose to help install the chute rod and connect it to the control assembly. Install Discharge Chute Crank 1. Remove the cover from the gear assembly on the discharge chute. 2. Release the lock teeth on the gear assembly with your finger and rotate the discharge chute 90° left. 3. Remove and save the hairpin from the control assembly underneath the control panel. NOTE: Do not remove the pin installed on the chute rod. NOTE: To ensure the discharge chute follows its full range of travel, make sure the control lever is pushed all the way to the left before installing and pinning the chute rod. 4. Align the holes on the end of the chute rod with the mark on the gear assembly and slide the end without a pin through the gear assembly, through the loop on the chute lock cable and into the hex hole in the control assembly. IMPORTANT: The loop will prevent the control cable from contacting the engine or muffler guard. If the loop gets damaged, loosely tie the cable to the control rod. NOTE: After the chute rod has been inserted through the hex hole in the control assembly, placing the unit in the service position (see Service Position on page 19) will ease alignment and installation of the hair pin. 5. Secure the chute rod to the control assembly with the hair pin removed in step 3 using the proper hole location as shown in Figure 7. Insert the hair pin with the loop end to the left of the chute rod so the control assembly follows a full range of travel. Figure 5 1.Mounting Hardware 2.Discharge Chute 3.Chute Pedestal 4.Discharge Chute Ring 1 1 3 2 OS7040 OS7045 4 Figure 6 1.Chute Rod 2.Gear Cover 3.Control Assembly 4.Hair Pin 1 3 2 4 OS7060 GB - 11 6. Insert the chute lock cable fitting into the bracket on the chute pedestal, and then connect the chute lock cable to the lock teeth by fitting the cable ball end into the slot on the lock teeth. NOTE: Press down on lock teeth with your finger to align the cable ball end with the slot. 7. Replace the gear cover removed in step 1. IMPORTANT: Rotate the discharge chute to the left when tightening the pedestal hardware to ensure clearance between the discharge chute and the belt cover. 8. Tighten pedestal hardware to 15–31 lbf-ft (20-42 N•m). 9. Make sure the discharge chute rotates left and right when you push the discharge chute c...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: