Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
NOTE: DO NOT use primer to restart a warm engine after a short shutdown. NOTE: Additional priming may be necessary if the temperature is below 15° Fahrenheit. 3. Grasp the recoil starter handle and slowly pull the rope out. At the point where it becomes slightly harder to pull the rope, slowly allow the rope to recoil. 4. Pull the starter handle with a firm, rapid stroke. Do not release the handle and allow it to snap back. Keep a firm hold on the starter handle and allow it to slowly recoil. 5. As the engine warms, slowly rotate the choke control to the OFF position. If the engine falters, quickly rotate the choke control back to the FULL position and then slowly into the OFF position again. NOTE: Allow the engine to warm up for a few minutes after starting. The engine will not develop full power until it reaches operating temperatures. Stopping The Engine Run engine for a few minutes before stopping to help dry off any moisture on the engine. 1. Move throttle control to STOP position. 2. Remove the ignition key and store in a safe place. 3. Wipe all snow and moisture from the area around the engine as well as the area in and around the drive control and auger control. Also, engage and release both controls several times. 10 11 To Engage Drive 1. With the engine running near top speed, move shift lever to one of six FORWARD positions or two REVERSE positions. Select a speed appropriate for the snow conditions that exist. 2. Squeeze drive control against the right handle and the snow thrower will move. Release it and the drive motion will stop. 3. To turn the unit left or right, squeeze the respective wheel steering control. See Figure 12. To Engage Augers 1. To engage augers and start snow throwing, squeeze the left hand auger control against the left handle. Release to stop augers. 2. While the auger control is engaged, squeeze the drive control to move, release to stop. Do not shift speeds while the drive is engaged. NOTE: This same lever also locks auger control so you can turn the chute control without interrupting the snow throwing process. 3. Release the auger control; the interlock mechanism should keep the auger control engaged until the drive control is released. 4. Release the drive control to stop both the augers and the wheel drive. To stop the auger, both levers must be released. Figure 13 When selecting a Drive Speed, use the slower speeds until you are comfortable and familiar with the operation of the snow thrower. NEVER reposition the shift lever (change speeds or direction of travel) without first releasing the drive control and bringing the snow thrower to a complete stop. Doing so will result in premature wear to the snow thrower’s drive system. WARNING The muffler, engine and surrounding areas become hot and can cause a burn. Do not touch. 4 Operating Your Snow Thrower Auger Control Test Perform the following test before operating your snow thrower for the first time and at the start of each winter. Check the adjustment of the auger control as follows: 1. When the auger control is released and in the disengaged “up” position, the cable should have very little slack. It should NOT be tight. 2. In a well-ventilated area, start the snow thrower engine as instructed on the previous page. Make sure the throttle is set in the FAST position. 3. While standing in the operator’s position (behind the snow thrower), engage the auger. 4. Allow the auger to remain engaged for approximately ten (10) seconds before releasing the auger control. Repeat this several times. 5. With the throttle control in the FAST (rabbit) position and the auger control in the disengaged “up” position, walk to the front of the machine. 6. Confirm that the auger has completely stopped rotating and shows NO signs of motion. If the auger shows ANY signs of rotating, immediately return to the operator’s position and shut off the engine. Wait for ALL moving parts to stop before re-adjusting the auger control. 7. To readjust the control cable, loosen the upper hex nut on the auger cable bracket. 8. Position the bracket upward to provide more slack (or downward to increase cable tension). See Figure 13. 9. Retighten the upper hex nut. 10.Repeat Auger Control Test to verify proper adjustment has been achieved. To Engage Drive 1. With the engine running near top speed, move shift lever to one of six FORWARD positions or two REVERSE positions. Select a speed appropriate for the snow conditions that exist. 2. Squeeze drive control against the right handle and the snow thrower will move. Release it and the drive motion will stop. 3. To turn the unit left or right, squeeze the respective wheel steering control. See Figure 12. To Engage Augers 1. To engage augers and start snow throwing, squeeze the left hand auger control against the left handle. Release to stop augers. 2. While the auger control is engaged, squeeze the drive control to move, release to stop. Do not shift speeds while the drive is engaged. NOTE: This same lever also ...