Оценок - , средний балл: ( )

Инструкция по эксплуатации Simplicity, модель 1691522

Производитель: Simplicity
Размер: 1.46 mb
Название файла:

Язык инструкции:

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Tighten the setscrew. Raise the snowthrower and recheck the measurement. Readjust if necessary. 3. The scraper blade will float over the surface bumps or dig into them depending on the down pressure. The initial adjustment made during snowthrower installation may be suitable. If not, fully raise the snowthrower. Loosen the setscrew in the rear set collar (D). To allow scraper blade to float more, move the rear set collar toward the rear. To increase down pressure, move the rear set collar toward the spring (C). Tighten the setscrew. Lower the lift lever. A WARNING On tractors with hydraulic lift levers, keep hands and feet from under snowthrower when snowthrower is in raised position. Snowthrower may lower when engine is off. Figure 17. Lift Rod Adjustment A. Front Set Collar B. Rod Guide C. Spring D. Rear Set Collar E. Lift Rod 14 Simplicity Assembly ATTENTION SETUP PERSONNEL: As setup personnel you have an obligation to know the product better than the customer. This includes safety related items. Prior to actual setup, thoroughly familiarize yourself with the tractor Operator’s Manual. Pay special attention to all safety warnings. It is possible during setup to place yourself in a position which is more hazardous than when the unit is in operation. Remember, it is your responsibility to set up the product safely and to know it well enough to be able to instruct a customer in the safe use of his power unit. Safety is a matter of common sense ... A matter of thinking before acting. Most shops have specific safety practices. Follow them. The precautions listed in the Operator’s Manual should not supersede existing practices but should be considered as supplemental information. CONTENT OF SECTION The snowthrower is shipped only partially assembled for packaging reasons. This section provides the necessary instructions for assembling the snowthrower. ASSEMBLY Remove all loose parts, the skin pack, and the snowthrower from the shipping carton. Open the skin pack and hardware bags and arrange all parts according to size and type. Then proceed as follows: NOTE Refer to chart inside back cover to identify screws, nuts and washers. 1. Install support bracket (C, figure 18) as shown with 3/8x1 capscrews and flange locknuts (A & B). NOTE Do not let pivot bearing along support the full weight of control rod, as the bearing can be damaged. 2. Insert end of spout control rod (E, figure 18) through plastic pivot bearing (D) on auger housing. Install a 3/32 x 5/8 inch (2.4 x 16 mm) cotter pin in the lower rod hole on the inside of the housing, and spread cotter pin legs fully around rod. Pull the rod back so cotter pin is up against pivot bearing and install another cotter pin through the rod just above the bearing. Spread cotter pin legs fully around the rod. 3. Place the thin plastic liner (G, figure 18) inside the rod guide (H). 4. Install rod guide and liner over spout control rod as shown. Attach rod guide to support bracket with a 5/16 x 1-1/8 capscrew and a locknut (F & I, figure 18). Tighten locknut (usually flush with end of capscrew) so control rod is held firmly but is still free enough to turn inside of rod guide. A. Capscrews B. Flange Locknuts G. Plastic Liner C. Support Bracket H. Rod Guide D. Pivot Bearing I. Locknut E. Control Rod J- Spout Extension Figure 19. Installing Control Cable A. Cotter Pin C. Lockwasher B. Cup Washer D. Nut 15 Assembly 5. Install the spout extension (J, figure 18) on the housing openings so the clip (K) on the housing is positioned in the notch on the spout extension. Then rotate spout extension slightly to start its rim under the clip. Oil mating surfaces so spout extension rotates freely. 6. Witht the spout extension facing slightly left, wind the cable around the control rod spool as shown in figure 19. Wind three turns on the rear part of the spool so that the cable leaves the spool on the lower edge as shown. Wind two turns on the front part of the spool so that the cable leaves the spool on the upper edge as shown. If necessary, loosen the cable clamp and then retighten after winding the cable. 7. Place the looped end of the cable over the stud on the spout extension (see figure 19). Place the small flat washer provided on the stud. Pull the other end of the cable around the stud as shown with a pliers. While holding the cable tight, install the cup washer (facing inward), lockwasher and nut to hold the cable. Tape any loose cable neatly to the taut cable. 8. Attach the deflector (J, figure 20) to the spout extension with two screws (H), washers (G), spacers (F), washers (A), lockwashers (E) and nuts (D). A. Washer, 5/16 F. Spacer B. Wing Nut G. Washer, 5/16 C. Locknut, 5/16 H. Screw, 5/16 D. Nut, 5/16 I. Carriage Bolt, 5/16 E. Lockwasher, 5/16 J. Deflector Figure 21. Snowthrower Pulley Belt Stop A. Belt Stop B. Capscrew C. Plain Washer 9. Install the two clips (I, figure 22) as shown with four capscrews (P) and flange loc...