Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Ignition Key The ignition key is a safety devise. It must be fully inserted in order for the engine to start. Remove the ignition key when the snow thrower is not in use. Important: Do not turn the ignition key in an attempt to start the engine. Doing so may cause it to break. Figure 4-1 Drive Control Headlight Oil Fill Fuel Cap Primer Choke Ignition Key Oil Drain Starter Button Electric Starter Outlet Recoil Starter Handle Chute Assembly Clean-Out Tool Auger Control Shift Lever Two-Way Chute Control™ Wheel Steering Control Chute Directional Control Skid Shoe Augers Controls and Features 4 11 Primer Bulb Pressing the primer bulb forces fuel directly into the engine’s carburetor to aid in starting a “Cold” engine. NOTE: Do not use the primer bulb to restart a warm engine after a short shutdown. Oil Fill Engine oil level can be checked and oil added through the oil fill. Skid Shoes Position the skid shoes based on surface conditions. Adjust upward for hard-packed snow. Adjust downward when operating on gravel or crushed rock surfaces. Electric Starter Outlet Requires the use of a three-prong outdoor extension cord and a 120V power source/wall outlet. Recoil Starter Handle This handle is used to manually start the engine. Electric Starter Switch Pressing the button on the top of the electric starter switch engages the engine’s electric starter when plugged into a 120V power source. Augers When engaged, the augers rotate and draw snow into the auger housing. Chute Assembly Snow drawn into the auger housing is discharged out the chute assembly. Fuel Cap Remove the gas cap to add gasoline to the fuel tank. Auger Control The auger control is located on the left handle. Squeeze the control grip against the handle to engage the augers and start snow throwing action. Release to stop. Drive Control / Auger Clutch Lock The drive control is located on the right handle. Squeeze the control grip against the handle to engage the wheel drive. Release the handle to stop. The drive control also locks the auger control so that you can operate the chute directional control without interrupting the snow throwing process. If the auger control is engaged simultaneously with the drive control, the operator can release the auger control (on the left handle) and the augers will remain engaged. Release both controls to stop the augers and wheel drive. NOTE: Always release the drive control before changing speeds. Failure to do so will result in increased wear on your machine’s drive system. sectiOn 4— cOntrOls and features Two-Way Chute Control™ The two-way chute control is located on the left side of the dash panel and is used to control the distance of snow discharge from the chute. • To change the upper chute angle to control the distance that snow is thrown, pivot the lever forward or backward. • Move the lever forward to pivot the upper chute down and reduce the distance snow is thrown. CHUTE DIRECTIONAL CONTROL DISCHARGE LEFT DISCHARGE RIGHT CHUTE TILT DOWN CHUTE TILT UP • Move the lever rearward to pivot the upper chute upward and increase the distance snow is thrown Chute Directional Control The chute directional control is located on the left side of the snow thrower. • To change the direction in which snow is thrown, crank clockwise to discharge to the left and counterclockwise to discharge to the right. Wheel Steering Controls The left and right wheel steering controls are located on the underside of the handles. Squeeze the right control to turn right; squeeze the left control to turn left. NOTE: Operate the snow thrower in open areas until you are familiar with these controls. Chute Clean-Out Tool WARNING! Never use your hands to clear a clogged chute assembly. Shut off engine and remain behind handles until all moving parts have stopped before unclogging. The chute clean-out tool is conveniently fastened to the rear of the auger housing with a mounting clip. Should snow and ice become lodged in the chute assembly during operation, proceed as follows to safely clean the chute assembly and chute opening: 1. Release both the Auger Control and the Drive Control. 2. Stop the engine by removing the ignition key. 3. Remove the clean-out tool from the clip which secures it to the rear of the auger housing. 4. Use the shovel-shaped end of the clean-out tool to dislodge and scoop any snow and ice which has formed in and near the chute assembly. 5. Refasten the clean-out tool to the mounting clip on the rear of the auger housing, reinsert the ignition key and start the snow thrower’s engine. 6. While standing in the operator’s position (behind the snow thrower), engage the auger control for a few seconds to clear any remaining snow and ice from the chute assembly. Head Light It can be tilted by loosening the screws on the side of its housing, position the light in the desired location and then retighten the screws. sectiOn 4 — cOntrOls and features Operation Starting The Engine 1. Attach spark plug wire to spark plug. Make certain ...
Эта инструкция также подходит к моделям:Снегоочистители - 928 SWE (2.81 mb)