Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
Your Caller ID unit enables you to: • Identify callers before you answer the phone. • View the time and date of each incoming call. • Record up to 80 incoming calls sequentially. • Know who called while you were away. REMINDER: This product requires a subscription to Caller ID service from your telephone company. Model 2-9016C / 2-9023 15377150 ( Rev. 0 E/F) 98-04 Printed in China BEFORE YOU BEGIN PARTS CHECKLIST Make sure your package includes the following items: MODULAR JACK REQUIREMENTS You need an RJ11 (CA11A) type modular jack, which is the most common type of phone jack and might look like the one pictured here. If you don’t have a modular jack, call your local phone company to find out how to get one installed. POWERING THE CALLER ID UNIT INSTALLING THE BATTERIES Disconnect the line cords from the back of the unit and wait a few seconds for the unit to go into standby. 1. Use a screwdriver or other flat tool to open the battery compartment door. 2. Insert 3 “AAA” size batteries as shown on the diagram in the battery compartment. 3. Close the battery compartment door securely. LOW BATTERY INDICATOR If the LOW BATTERY Text and Indicator appears in the display, you need to replace the batteries. It is important that you replace the batteries as soon as possible to guarantee reception of the Caller ID signals. When you replace the batteries, your Caller ID unit retains stored information for up to 60 seconds. It is still a good idea to write down information that you do not want to lose. INSTALLATION WITH A STAND-ALONE ANSWERING MACHINE The answering machine must be set to answer calls after at least 2 rings to properly receive Caller ID information. To use your Caller ID unit with an answering machine: 1. Plug a telephone line cord into either jack on the back of the Caller ID unit and into the Modular Jack on the wall. 2. Plug another telephone line cord into the remaining jack on the back of the unit into the answering machine Input/Line jack. 3. Plug a third telephone line cord into the answering machine Phone jack and into the telephone. MESSAGE INDICATORS The following special messages indicate the status of a message or the unit: NO CALL The caller memory is empty. UNKNOWN CALL The incoming call does not have Caller ID service or their service area is not linked to yours. If UNKNOWN NAME appears with a calling number, the name information was not available for that number. REPLACE BATTERY Battery power level is low and batteries must be replaced. BLOCKED CALL The caller of the incoming call is registered as “Private Number” and their Caller ID information is withheld. ERROR Caller ID information has been corrupted during transmission. NO DATA No Caller ID signal has been detected, or Caller ID service has not been activated. START/END The Caller ID memory log is at the START/END of the point. Caller ID User’s Guide TROUBLESHOOTING TIPS NO DIAL TONE ON THE PHONE ATTACHED TO THE CALLER ID UNIT • Check all cabling to make sure that all connections are secure. NO DISPLAY • Check for proper battery installation. NO INFORMATION IS SHOWN AFTER THE PHONE RINGS • NO DATA appears in the display if no Caller ID signal has been detected, or Caller ID service has not been activated by your local telephone company. • Be sure to wait until the second ring before answering. ERROR MESSAGE IS DISPLAYED • ERROR appears in the display if the unit detects anything other than valid Caller ID information during the silent period after the first ring. This message indicates either the presence of noise on the line, or that an invalid message has been sent from the telephone company. REN NUMBER On the bottom of this equipment is a label indicating, among other information, the FCC Registration number and Ringer Equivalence Number (REN) for the equipment. You must, upon request, provide this information to your telephone company. The REN is useful in determining the number of devices you may connect to your telephone line and still have all of these devices ring when your telephone number is called. In most (but not all) areas, the sum of the RENs of all devices connected to one line should not exceed 5. To be certain of the number of devices you may connect to your line as determined by the REN, you should contact your local telephone company. SERVICE Thomson Consumer Electronics Canada, Inc. warrants to the purchaser or gift recipient that if any manufacturing defect becomes apparent in this product within 1 year from the original date of purchase, it will be replaced free of charge, including return transportation. This warranty does not include damage to the product resulting from accidents, misuse or leaking batteries. Should your product not perform properly during the warranty period, either: 1. Return it to the selling dealer with proof of purchase for replacement, OR 2. Remove the batteries (where applicable), and pack product complete with accessories in the original carton (or equivalent). — Mail prepaid (with ...
Эта инструкция также подходит к моделям:Проводные телефоны - 23-Feb (60.47 kb)