Оценок - 4, средний балл: 4.3 ( )

Производитель: Ariens Размер: 9.06 mb Название файла: Язык инструкции:

IMPORTANT: Gradually open choke after engine starts. Throttle The throttle controls the engine speed. To increase or decrease the engine speed, adjust to: 1. Fast (normal or warm starts) 2. Part-Throttle 3. Slow (cold weather starts) 4. Stop (engine is off) Electric Starter The electric starter will start a properly choked and cranked engine when the starter button is pushed. Refer to Starting and Shut Off on page 20. Recoil Starter Handle When pulled, handle will turn engine over. IMPORTANT: DO NOT let handle snap back against starter. Snow Clean-Out Tool (Figure 15) To clear the discharge chute: 1. Shut off the engine. 2. Wait 10 seconds and make sure impeller blades have stopped rotating. 3. Remove the snow clean-out tool (1) from the auger housing and use it to remove the clog from the discharge chute. 4. Replace the snow clean-out tool on the auger housing. Deflector Remote (921004, 006, 007, 008, 009) Place deflector into position before operation. DO NOT throw snow any higher than necessary. Place deflector remote in a forward notch to throw snow lower. Place deflector remote in a rearward notch to throw snow higher. Discharge Deflector (921005) ALWAYS position discharge chute deflector at a safe angle before starting engine. DO NOT throw snow any higher than necessary. 1. Push deflector handle forward or down to throw snow lower. 2. Pull deflector handle up or to the rear to throw snow higher (Figure 16). OS1196 6 1 1 2 2 1 4 3 2 1 WARNING: Hand contact with the rotating impeller is the most common cause of injury associated with snow throwers. Never use your hand to clean out the discharge chute. 1 Figure 15 OS7102 GB - 18 Discharge Chute Discharge chute rotates 200°. ALWAYS position discharge chute in safe direction and angle, away from operator and bystanders, before starting engine. Discharge Chute Control (921004, 006, 007, 008, 009) IMPORTANT: If chute does not stay in set position, adjust as directed in SERVICE AND ADJUSTMENTS on page 24, or repair before operation. Rotate the Chute with Discharge Chute Control. IMPORTANT: DO NOT force frozen chute controls. If frozen, take to warm place until controls are free. Discharge Chute Crank (921005) IMPORTANT: If chute does not stay in set position, adjust as directed in SERVICE AND ADJUSTMENTS on page 24, or repair before operation. Rotate the Chute with Discharge Chute Crank. IMPORTANT: DO NOT force frozen chute controls. If frozen, take to warm place until controls are free. Remote Wheel Lock (921005) Squeeze and release the remote wheel lock control to lock the left wheel for better traction when throwing snow or to unlock the left wheel for easier steering. NOTE: The wheel lock will not release when under load. Do not unlock the wheel while turning. If the wheel lock will not release, turn the unit slightly left or right to relieve axle load and release the axle lock. If remote wheel lock does not lock or unlock properly, adjust or repair before operation (see Remote Wheel Lock (921005) on page 25). Scraper Blade The scraper blade allows the back of the housing to keep better contact with the surface being cleared. It also prevents damage to the housing from normal wear. IMPORTANT: DO NOT allow Scraper Blade to wear too far or Auger/Impeller housing will become damaged. Runners The runners control the distance between the scraper blade and the ground. Adjust runners equally to keep blade level with the ground. Refer to Pre-Start on page 19 for recommended settings. Figure 16 OS7103 1 1. Deflector Handle 921005 Figure 17 OS7105 921004, 006, 007, 008, 009 Figure 18 OS7106 921005 GB - 19 Track Angle (921007, 008, 009) (Figure 19) The track angle can be adjusted to position the auger housing for level clearing, deep cutting or transport. Squeeze the handlebar trigger and press down on the handlebars to move the auger housing into an up position. Release the trigger to hold the position. Lift up on the handlebars and squeeze and release the handlebar trigger to move the auger housing into a down position. FILLING FUEL TANK Fuel Shut-Off Valve IMPORTANT: The fuel shut-off valve MUST be in the closed position prior to transporting the unit. The fuel shut-off valve has two positions: To add fuel to fuel tank: 1. ALWAYS place unit in open or wellventilated area. 2. Stop engine and allow to cool. 3. Clean Fuel Cap and surrounding area to prevent dirt from entering Fuel Tank. 4. Remove Cap. IMPORTANT: DO NOT use gasohol or gasoline containing alcohol. See Engine Manual for correct type and grade of fuel. 5. Fill fuel tank to within 1/2 in. (1.2 cm) below bottom of filler neck with unleaded gasoline. NOTE: Tank capacity is 1 gallon (3.8 liters). 6. Replace Fuel Cap and tighten. 7. ALWAYS clean up any spilled fuel. PRE-START 1. Frozen Impeller IMPORTANT: Before starting engine, check impeller to be sure it is not frozen. To check impeller: 1. With ignition key switch in “Stop” position, squeeze Attachment Clutch Lever to Engaged position. 2. Pull Recoil Sta...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: