Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Mounting Mounting your scope properly is important to the accuracy and durability of your firearm and scope. Proper mounting assures that the scope is aligned to the barrel and the scope is rigged to the rifle for accuracy. We recommend using the Millett Picatinny rail and Millett Angle-Loc ™ rings. Using the base and ring combination that you have chosen, make sure mounting screws for the base are firmly tightened. On most bolt action rifles, 50 to 60 inch pounds is suitable for the torque. Loctite® Is recommended to prevent the screws loosening under recoil. Place the bottoms of the rings onto the base and center and tighten. Make sure ring bottom is aligned in base and not cocked or out of line with the bore. Failure to align the base and bottom of the rings can damage the scope. Lay the scope into the bottoms of the rings, with the eyepiece to the rear, and align the crosshairs to the vertical and horizontal, moving the scope back and forth to get a full sight picture. While looking through the scope, align the crosshairs and the eye relief. The eye relief on this model scope should be about 75mm or 3 inches. Place the top caps of the rings on the bottoms and slightly tighten the screws. Check the alignment and eye relief before fully tightening the cap screws. Boresighting Boresighting is aligning the scope to the bore of the rifle to assist you in getting on target when sighting in the rifle. There are several ways to boresight a rifle, 1. Looking through the scope and the bore of the rifle until they are both at the same point. 2. Using an optical device inserted into the bore and aligning the scope to a point on the boresighter. 3. Using a laser inserted into the barrel at the muzzle or chamber to make a reference point and aligning the scope crosshairs to that point. All of these systems work well, follow the instructions supplied with each method. Sighting in Sighting in your rifle is critical to assure that point-of-aim and impact yards are the same at a known range. The method we recommend is to start shooting at 25 yards or 50 yards with a target large enough to allow some room for error. The goal of properly sighting in the scope is to eliminate human error, so use a solid rest to support the rifle. It’s best if at the time you sight in, the wind is calm. Fire 3 shots, carefully holding the crosshairs at the same point on the target for each shot. Measure the distance from the point you were aiming at and center of the 3 shot group. This is how much you will need to move your scope to align the crosshairs. Let’s say the group was 4 inches to the right and 5 inches high. Since the adjustments on the TRS scopes are 1/8” or 3mm at 100, and 1/16” at 50 yards, you will need to move the scope adjustments 64 clicks to the left and 80 down. One full turn of the turret is 72 clicks or 9 inches at 100 yards. Note: The arrows on the turrets of the scope are for direction of movement of the bullet. Move the target to 100m or yards and repeat the sighting in procedure to adjust the turrets until the scope is aligned to the rifle. Fire a group after adjustment to assure the proper sight-in. It is best to fire the rifle at the ranges that the sight will be using to assure your zero and drop for various ranges. Many shooters set the sights a number of inches high at 100 yards so they have a longer point-blank range. Example, a 308 sighted 2 inches high at 100 will be dead on at 200 yards, extending the point blank range to over 300 yards. Once the scope is sighted in, you can zero the windage and elevation turrets by loosening the 3 small set screws in the top of the caps and turning the cap until the zero ( 0 ) lines up with the dot on the body of the scope and then retighten the screws. Now it’s easy to count the clicks for elevation and windage. Note: Small Allen wrench in box. Using the features of the TRS scopes The TRS was designed to give the shooter the most useful features needed under the most demanding use and conditions. To get the full benefit of the features it’s best to learn their use before needing them. Try the different TRS features before you need them under varying conditions. Eye Piece Focus Windage Elevation Turret Lock Rings Range Focus Zoom Control Illuminator Illumination of the crosshairs On the rear of the scope there is a small knob that has markings from off to 10. This is your control for illumination of the crosshairs in low light or when you want a high contrast to the target. Use the lowest setting that still gives good visibility to the target and the crosshairs. NV is for use with Night Vision devices or under the lowest light conditions. The battery life of the illumination is about 50 hours at the highest setting and over 150 for the lowest. Turn the illumination off when not in use. It’s best to have a spare battery with you in the field in case a new battery is needed. NOTE: When the illumination is turned on at night, it can be seen from directly in front of the scope,...
Эта инструкция также подходит к моделям:Снаряжение для охоты - TRS-2 (156.53 kb)