Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
. The fixture must have a minimum of 1 meter distance from combustible materials. 1. Clamp 2. Fixture Yoke 3. Angle Adjustment 1 2 3 Rigging The fixture includes a mounting yoke to which 1 rigging clamp can be bolted. 1. Align the clamp screw with the center hole on the yoke and tighten. 2. Verify the structure can hold 10 times the weight of all to-be installed fixtures. 3. Adjust the angle on the yoke arm as necessary. Q-Scan 250 & Q-Roll 250 User Manual 8 2005-11-15/13:24 OPERATING INSTRUCTIONS E Control Panel On the control panel you can set the DMX address, set the fixture to Master/Slave mode, reset the fixture and change fixture personality traits. Control Board Enter Choose Up Down .... [Enter] Confirms selection [Choose] Access to main menu [Up] Toggle menu items in a forward direction [Down] Toggle menu items in a reverse direction Control Panel Functions FUNCTION OPTIONS NOTES ... ../.. Pan invert ... ../.. Tilt invert ... ../.. Fixture reset ... ../.. Stand Alone (Sound-Active) ... ../.. Stand Alone (Auto Run) ... ../.. Reserved ... ../... (-n) to Enable Channel 7Pan/Tilt Speed) ... ../.. Display invert ..... ...~... DMX channel addressing -y: Activates setting -n: Disables, skips or selects alternative setting Applying changes to Functions (Quick Instructions) Unless other wise stated changes in the control panel can be applied in the following manner. 1. Press [Choose] button repeatedly until the display reads the menu function you wish to change as illustrated in the table above in section .Control Panel Functions.. 2. The display will read the previously stored settings for the desired function, for example, either with a .-y. ora .-n. as in .P1-y or P1-n.. s 3. Press the [Up] or [Down] button to toggle between either the .-y. or .-n. selection for that sparticular menu function. 4. Press the [Enter] button to store your selection. The display will read .PASS. to confirm your sselection Q-Scan 250 & Q-Roll 250 User Manual 9 2005-11-15/13:24 Operating Modes . A stand-alone mode will listen to sound and run through its diverse range of built in programs. . Master/Slave mode will allow the command of up to as many units you want in a synchronized light show to the sound. . DMX control mode will provide the greatest flexibility and creativity. Each fixture trait can be controlled individually using any universal DMX-512 controller. Master & Stand Alone (P6) In order to create the correct environment for Stand Alone Note! operation, several parameters have to be set in the control If the fixture is connected to a panel. Please make the changes to the functions as listed in controller, please disconnect it. the table below. The display will read the previously FUNCTION SET TO NOTES P6 -y Master mode (one Master only) P4 -y Sound activated A 001 Channel address P1 Any Pan invert P2 Any Tilt invert selected setting. Only one fixture can be the Master assigned fixture. However, 16 units can be slaved to the master unit. Setting Slave Fixtures The Master/Slave mode will allow you to link multiple units in a daisy chain fashion. In this mode, the first unit in the daisy chain, the master, will automatically command all other units following. The first unit will operate in a Stand/Alone mode and all units following will synchronize to the first unit. Up to 16 fixtures can be daisy chained in Master/Slave mode. MENU SET TO NOTES P6 -n Master mode P4 -n Sound activated A 001 Channel address P1 Any Pan invert P2 Any Tilt invert You can change the Pan and Tilt settings freely. Sound-active (P4) or Auto-run (P5) In Master/Slave mode you can choose whether the fixture will run in a sound-active state where the movement is triggered by sound or in auto-run where the speed is pre-programmed. MENU SET TO NOTES P4 -n Sound Activated or P5 -n Auto-run Q-Scan 250 & Q-Roll 250 User Manual 10 2005-11-15/13:24 Operating Instructions DMX Mode Operating in a DMX Control mode environment gives the user the greatest flexibility when it comes to customizing or creating a show. You can tailor your programming to suit a specific event. Whether it is a wedding where a spot light may be required or a lead singer requiring a color solo, the opportunities are endless. In this mode you will be able to control each individual trait of the fixture independently. Daisy Chain Connection 1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of the first fixture. 2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then, proceed to connect from the output as stated above to the input of the following fixture and so on. Daisy Chain Connection Menu Functions DMX-512 addressing This mode enables the use of a universal DMX controller device. Each fixture requires a "start address" from 1 to 511. A fixture requiring one or more channels for control begins to read ...
Эта инструкция также подходит к моделям:Сканеры/копиры/мфу - Q-ScanTM 250 (455.91 kb)