Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
NOTE The dedicated scanner driver is installed after the Scanning Utility has been installed. 1 Turn ON your computer, and log on to Windows. IMPORTANT Be sure to log on as the Administrator. 2 Insert the setup disc into the disk drive. This manual assumes that “D” is assigned to your disk drive. 3 Click [Start], and then click [All Programs]. The procedure in Windows XP is different from the ones described in this manual. Refer to the Windows XP “Help and Support Center” to select [Run]. 12 4 Click [Accessories], and then click [Run]. 5 Enter “D:\SU80\setup.exe” in the [Open] fields, and then click [OK]. Installation starts. 6 Follow the instructions on the screen to complete the installation. IMPORTANT The computer may need to be restarted, after the installation, depending on the operating system. If this is necessary, make sure to restart the computer. Connecting the Scanner to a Computer The only way to connect the scanner to your computer is with a USB cable. IMPORTANT • Be sure to use the USB cable bundled with the scanner or a Hi- Speed USB 2.0 compatible cable with the length less than 5 m. • When the application is running, do not turn the scanner OFF or unplug the interface cable. • Do not connect multiple CR-50/80 scanners to one computer. CAUTION • Do not turn OFF the scanner or remove the interface cable when an application is running. • Turn OFF the computer and the scanner before changing the cable. USB Connections Connect the scanner and the computer with the cable provided or a Hi-Speed USB 2.0 cable. Type A Plug Type B Plug USB Connector NOTE Connect the type B plug (square) to the scanner and connect the type A plug (flat) to the USB port on the computer. 13 Connecting the Power Cord Connect the power cord. Make sure to use only the power cord provided with the scanner. WARNING When connecting the power cord, follow these precautions. Failure to do so may cause a fire or electrical shock. • Never grasp the power plug when your hands are wet. • Never plug the scanner into a multiplug power strip. • Never bundle or tie the power cord around itself or another object. Connect the power plug securely into the power outlet. • Use only the power cord and power plug provided with the scanner. • Before you connect the power cord, make sure to turn OFF the power switch. • Connect only to a power outlet of the rated voltage and power supply frequency (either 120 V, 60 Hz or 220-240 V, 50/60 Hz, depending on your region). • Do not plug the scanner into a power outlet shared with another device. If you use an extension cord, make sure that the extension cord is rated for the current requirements of the scanner. Turning ON and OFF the Power Follow the procedures below to turn the scanner power ON and OFF. Turning ON the Power 1 To turn ON the scanner, slide the Power Switch to the right. (ON) IMPORTANT • When you turn ON the power, the power LED lights and remains lit. • If the scanner does not work, there is a problem with the scanner. Turn OFF the power, and contact your local authorized Canon dealer or service representative to have the scanner serviced. WARNING If you hear strange sounds, detect smoke or abnormal heat, sense a vibration, or smell odd odors around the scanner, turn OFF the power immediately and disconnect the power cord from the power outlet. Contact your local authorized Canon dealer or service representative to have the scanner serviced. 2 Turn ON your computer. 14 3 Windows recognizes the CR-50/80 as new hardware, and installation starts automatically. (Windows 7) NOTE The CR-50/80 will be registered as “CANON CR-50 USB” or “CANON CR-80 USB” in the Imaging Device directory. Turning OFF the Power 1 Turn OFF your computer. 2 To turn OFF the scanner, slide the Power Switch to the left. (OFF) CAUTION • Wait at least 10 seconds before turning the scanner back ON. • For your safety, disconnect the power plug from the power outlet if you are not using the scanner for a long period of time. 15 Preparing the Ink Cartridge 1 Hook your finger around the open lever and open the Maintenance Cover. This section describes how to prepare the ink cartridge so that you can use the imprinter to print text on scanned documents. About the Ink Cartridge The ink cartridge is not included with the scanner. Purchase an ink cartridge separately, as shown below. Manufacturer : Hewlett Packard Ink Cartridge Blue : C6602B (Canon#3693A002) Ink Cartridge Red : C6602R (Canon#3693A003) Ink Cartridge Green : C6602G (Canon#3693A004) Setting the Ink Cartridge and Adjusting the Print Position 2 Remove the Imprinter Cover. The ink cartridge needs to be set to print. Set the ink cartridge according to the following procedure. You can adjust the print position to three different levels. IMPORTANT • To set the ink cartridge, turn the scanner OFF before removing the Maintenance Cover. After the ink cartridge is set, replace the Maintenance Cover, and then turn the scanner back ON. • Finish up the unpacked ink cartridge ...
Эта инструкция также подходит к моделям:Сканеры/копиры/мфу - CR-80 (1.39 mb)